DS200PTBAG1AEC模塊備件
低電平輸入
使用霍尼韋爾PMIO LLMUX FTA。每個FTA支持16個通道。支持兩種類型的LLMUX FTA。一個提供16個RTD輸入。另一個提供16個TC或MV輸入。FTA的任何組合可用于提供所需TC、mV或RTD點的混合。顯著特點?TC和RTD操作?遠程冷端能力?1秒PV掃描,帶OTD保護?可配置OTD保護(見下文)?溫度點可按16點增量添加溫度支持溫度輸入LLMUX支持現有固態PMIO LLMUX FTA。PMIO LLMUX FTA支持RTD和熱電偶(TC)輸入。以1秒的速率從所有點收集溫度變量。1秒更新包括在溫度變量傳播之前對開路熱電偶檢測(OTD)(見下文)的可配置檢查。所有TC輸入均使用冷端補償(CJT)裝置進行補償。采樣和開放式傳感器檢測溫度多路復用器支持RTD和熱電偶,在PV交付前進行開放式傳感器的檢測(如有配置)。在OTD配置激活的情況下,在同一測量窗口內執行OTD循環的同時,對PV進行采樣和保持。如果OTD為負,則PV通過系統向上傳播。
輸入通道軟故障被設置
如果OTD為正,則PV被設置為NAN,并且輸入通道軟故障被設置。這樣,對于因熱電偶開路而無效的PV值,不會發生不適當?shù)目刂苿?dòng)作。PV采樣/報告不會導致OTD處理的額外延遲。詳細規格–低電平輸入多路復用器參數規格輸入/輸出型號CC PAIM01 PMIO FTA型號1 MU-TAMR04、TAMT04、TAMT 14輸入型熱電偶和/或RTD輸入通道64完全隔離通道間、通道間PM和通道間電源,共16個通道增量。輸入掃描速率1秒由IOM固定(最多64個通道/秒)通道帶寬0至4.7 Hz(-3 dB)標稱輸入范圍(僅限TC)-20至+100毫伏最大正常模式連續輸入無損壞(配置任何熱電偶類型)-10至+10伏(TC)-1至+2伏@100毫安(RTD)增益誤差(-20至+10毫伏范圍)0.050%滿量程最大溫度穩定性TC,毫伏輸入+/-20 ppm每攝氏度最大RTD輸入+/-20 ppm/攝氏度最大長期漂移500 ppm
Low level input
Use Honeywell PMIO LLMUX FTA. Each FTA supports 16 channels. Two types of LLMUX FTA are supported. One provides 16 RTD inputs. The other provides 16 TC or MV inputs. Any combination of FTA can be used to provide the required mix of TC, mV or RTD points. Remarkable features ? TC and RTD operation ? Remote cold end capability ? 1-second PV scanning with OTD protection ? Configurable OTD protection (see below) ? Temperature point can be added in 16 point increments to support temperature input LLMUX to support existing solid-state PMIO LLMUX FTA. PMIO LLMUX FTA supports RTD and thermocouple (TC) inputs. Collect temperature variables from all points at a rate of 1 second. The 1-second update includes a configurable check of the open thermocouple detection (OTD) (see below) before the temperature variable propagates. All TC inputs are compensated by the cold junction compensation (CJT) device. The sampling and open sensor detection temperature multiplexer supports RTD and thermocouple, and carries out open sensor detection (if configured) before PV delivery. When OTD configuration is activated, PV is sampled and held while OTD cycle is executed in the same measurement window. If OTD is negative, PV propagates upward through the system.
Input channel soft fault is set
If OTD is positive, PV is set to NAN and input channel soft fault is set. In this way, improper control action will not occur for PV value invalid due to thermocouple open circuit. PV sampling/reporting does not cause additional delays in OTD processing. Detailed specification - Low level input multiplexer parameter specification Input/output model CC PAIM01 PMIO FTA model 1 MU-TAMR04, TAMT04, TAMT 14 Input thermocouple and/or RTD input channel 64 completely isolate power supply between channels, PM between channels and between channels, with a total of 16 channel increments. Input scan rate 1s fixed by IOM (up to 64 channels/s) Channel bandwidth 0 to 4.7 Hz (- 3 dB) Nominal input range (TC only) - 20 to+100 mV Maximum normal mode Continuous input without damage (any thermocouple type configured) - 10 to+10 V (TC) - 1 to+2 V @ 100 mA (RTD) Gain error (- 20 to+10 mV range) 0.050% of full scale maximum temperature stability TC, Millivolt input+/- 20 ppm maximum RTD input per ° C+/- 20 ppm/° C maximum long term drift 500 ppm