330104-00-10-10-02-00傳感器
3300監測系統機架安裝和維護手冊
（129766-01）?標準系統的一般說明?三模塊冗余（TMR）系統的一般描述?從3300機架上安裝和移除模塊的說明?3300監測系統3300監測系統框架配置和實用指南（129777-01）中使用的所有電纜的圖紙?使用3300機架配置軟件設置模塊運行參數的指南?使用3300測試實用程序驗證模塊上的輸入和輸出端子是否正常運行的指南3300監控系統計算機硬件和軟件手冊（128158-01）?將機架連接到3300主計算機的說明?程序驗證通信?安裝軟件的程序?使用數據采集/DDE服務器和操作員顯示軟件的指南?設置網絡和遠程通信的程序和圖表3300現場接線圖包（130432-01）?顯示如何連接特定傳感器的圖表?推薦接線列表1.1目視接收檢查檢查模塊是否有明顯的運輸損壞。
如果運輸損壞明顯
向承運人提出索賠，并向本特利內華達公司提交一份副本。1.2搬運和儲存注意事項電路板包含暴露于靜電時容易損壞的設備。由于電路板的明顯不當操作造成的損壞將使保修失效。為避免損壞，請遵守以下預防措施。當從機架上卸下該模塊時，應用程序警報主機通信和機架配置功能將丟失。?不要將靜電放電到電路板上。避免使用會使電路板受到靜電損壞的工具或程序。一些可能的原因包括未接地的烙鐵、非導電塑料和類似材料。?在處理或維護印刷電路板之前，人員必須用合適的接地帶（如3M Velostat No.2060）接地。?用導電袋或箔運輸和儲存電路板。?在干燥的天氣要格外小心。小于30%的相對濕度會增加任何表面上的靜電積累。?正確執行時，可在機架通電時將該模塊安裝到機架中或從機架中卸下。有關正確程序，請參閱機架安裝和維護手冊（零件號129766-01）。1.3處置聲明在產品壽命結束或使用結束時控制產品的客戶和第三方全權負責正確處置產品。控制產品的任何個人、公司、公司、協會或機構不得以違反美國州法律、美國聯邦法律或任何適用國際法的方式處置產品。本特利內華達公司不負責產品壽命結束或使用結束時的處理
3300 Monitoring System Rack Installation and Maintenance Manual
(129766-01) ? General description of standard systems ? General description of three module redundant (TMR) systems ? Instructions for installing and removing modules from 3300 racks ? 3300 Monitoring System 3300 Monitoring System Rack Configuration and Utility Guide (129777-01) Drawings of all cables used in ? Guidelines for Setting Module Operating Parameters Using the 3300 Rack Configuration Software ? Guidelines for Verifying that the Input and Output Terminals on the Module Work Properly Using the 3300 Test Utility 3300 Monitoring System Computer Hardware and Software Manual (128158-01) ? Instructions for connecting the rack to the 3300 host computer ? Program verification communication ? Program for installing software ? Guidelines for using data acquisition/DDE servers and operator display software ? Procedures and diagrams for setting up network and telecommunications 3300 Field Wiring Diagram Package (130432-01) ? Diagram showing how to connect specific sensors ? Recommended wiring list 1.1 Visual receiving inspection Check the module for obvious transport damage.
If transport damage is obvious
Make a claim to the carrier and submit a copy to Bentley Nevada. 1.2 Handling and Storage Precautions The circuit board contains equipment that is easily damaged when exposed to static electricity. Damage caused by obvious improper operation of the circuit board will void the warranty. To avoid damage, observe the following precautions. When the module is removed from the rack, the application alerts host communication and rack configuration functions will be lost. ? Do not discharge static electricity onto the circuit board. Avoid using tools or programs that may damage the circuit board by static electricity. Some possible causes include ungrounded soldering irons, non-conductive plastics, and similar materials. ? Before handling or maintaining printed circuit boards, personnel must be grounded with a suitable grounding strap (such as 3M Velostat No.2060). ? Transport and store circuit boards in conductive bags or foil. ? Be extra careful in dry weather. A relative humidity of less than 30% will increase the accumulation of static electricity on any surface. ? When performed correctly, the module can be installed in or removed from the rack when the rack is powered up. Refer to the Rack Installation and Maintenance Manual (part number 129766-01) for the correct procedure. 1.3 Disposal Statement Customers and third parties who control the product at the end of its life or use are solely responsible for the correct disposal of the product. Any person, company, company, association or institution that controls the product shall not dispose of the product in a manner that violates U.S. state laws, U.S. federal laws or any applicable international law. Bently Nevada is not responsible for the disposal at the end of product life or use
