本特利3300系列帶鎧裝電纜330104傳感器 330010-02-02-00
每個變量都通過以下選項獨立配置
位置變量公制或英制單位滿量程濾波器直接濾波器1.2 Hz單極低通間隙濾波器0.41 Hz單極正常低通濾波器2.4 kHz單極通低通滿量程位置1至28 mm（50至1100 mils）量程，零位可調。間隙-24 V精度位置變量±滿量程輸入阻抗的1%不可配置10 k? 速度通道類型速度通道類型使用接近傳感器測量速度。速度變量速度變量是從原始傳感器信號中過濾和處理的測量值。速度高達4個速度測量間隙間隙，電壓可配置選項每個變量獨立配置有以下選項：間隙濾波器0.09 Hz單極低通OK濾波器2.4 kHz單極高通滿量程速度100-100000 rpm每轉事件EPR 0.001至1000精度速度變量：±0.5 rpm+0.015%讀數輸入阻抗不可配置10 k? 溫度輸入（通道5–8）通道5至8支持E、J、K和T型熱電偶以及2線和3線RTD。溫度變量溫度變量是從原始傳感器信號中處理的測量值。溫度通道類型為每個通道處理一個溫度變量?？膳渲眠x項每個變量通過以下選項獨立配置。單位°C或°F濾波器模擬濾波器50 Hz單極低通數字濾波器陷波濾波器將使50 Hz和60 Hz（49 Hz至61 Hz）的前5階衰減至少100 dB。
滿量程范圍
E型-200至1000oC（-328至1832oF）J型-210至1200oC? Cuα=0.00427-200至260oC（-328至500oF）1900/65A通用設備監視器數據表6/22 173401修訂版T 120? Niα=0.00672-80至260oC（-112至500oF）100? Ptα=0.00385:-200至850oC（-328至1562oF）100? Ptα=0.00392:-200至700oC（-328至1292oF）精度所有熱電偶類型在25°C（77°F）±2.5°C（±4.5°F）條件下的典型溫度為±1°C（？.8°F），熱電偶測量值超過-100°C（148°F）時的最大溫度為±5℃（？9°F）? Cu）±1.5°C（±2.7°F）+0.5%滿量程3線RTD 10? Cu±3°C（±5.4°F）+0.5%滿量程2線RTD類型2線RTDs由于現場線電阻和環境溫度變化導致的現場線電阻變化而存在額外誤差。輸入阻抗熱電偶輸入>1 MΩ報警狀態時間延遲位置/振動輸入最小0.1秒最大60秒調整分辨率0.1秒溫度/速度輸入最小1秒最大60秒鐘調整分辨率0.1秒鐘繼電器邏輯1900/65A監視器有六個繼電器輸出，用戶可以根據用戶定義編程打開或關閉觸點邏輯語句。邏輯語句使用任何通道或通道組合的OK、Alert和Danger狀態作為輸入。邏輯操作數和旁路通道被忽略，包括真和旁路通道或邏輯操作數監視器禁止監視器不正常監視器危險監視器警報通道不正常通道危險通道警報變量危險變量警報最大操作數50個繼電器繼電器配置以下配置選項獨立于繼電器邏輯，可為每個繼電器配置：l獨立于報警狀態的閉鎖或非閉鎖l常通電或常斷電l常開和常閉觸點繼電器規格類型
Each variable is configured independently through the following options
Position variable Metric or English units Full scale filter Direct filter 1.2 Hz Single pole low pass gap filter 0.41 Hz Single pole normal low pass filter 2.4 kHz Single pole low pass Full scale position 1 to 28 mm (50 to 1100 mils) Range, Zero position adjustable. Gap - 24 V accuracy position variable ± 1% of full scale input impedance is not configurable 10 k ? speed channel type speed channel type uses proximity sensors to measure speed. Velocity variable The velocity variable is the measured value filtered and processed from the original sensor signal. Speed up to 4 speed measurement gap, voltage configurable options Each variable is independently configured with the following options: Gap filter 0.09 Hz unipolar low-pass OK filter 2.4 kHz unipolar high pass full scale speed 100-100000 rpm per rev event EPR 0.001 to 1000 Precision speed variable: ± 0.5 rpm+0.015% reading input impedance Not configurable 10 k ? temperature input (channels 5 – 8) Channels 5 to 8 support E, J, K and T thermocouples as well as 2-wire and 3-wire RTDs. Temperature variable The temperature variable is the measured value processed from the original sensor signal. The temperature channel type handles one temperature variable for each channel. Configurable options Each variable is configured independently through the following options. Unit ° C or ° F filter Analog filter 50 Hz unipolar low-pass digital filter Notch filter will attenuate the first 5 orders of 50 Hz and 60 Hz (49 Hz to 61 Hz) by at least 100 dB.
Full scale range
Type E-200 to 1000 o C (- 328 to 1832 o F) Type J-210 to 1200 o C ? Cu α= 0.00427-200 to 260 o C (- 328 to 500 o F) 1900/65A Universal Equipment Monitor Data Sheet 6/22 173401 Rev T 120 ? Ni α= 0.00672-80 to 260 o C (- 112 to 500 o F) 100 ? Pt α= 0.00385:200 to 850 o C (- 328 to 1562 o F) 100 ? Pt α= 0.00392: - 200 to 700 o C (- 328 to 1292 o F) Accuracy Typical temperature for all thermocouple types is ± 1 ° C (± 1.8 ° F) at 25 ° C (77 ° F) ± 2.5 ° C (± 4.5 ° F), The maximum temperature when the thermocouple measurement value exceeds - 100 ° C (148 ° F) is ± 5 ℃ (± 9 ° F) ? Cu) ± 1.5 ° C (± 2.7 ° F)+0.5% full scale 3-wire RTD 10 ? Cu ± 3 ° C (± 5.4 ° F)+0.5% full scale 2-wire RTD type 2-wire RTDs have additional errors due to changes in field wire resistance due to changes in field wire resistance and ambient temperature. Input impedance Thermocouple input>1 M Ω Alarm state Time delay Position/vibration input min 0.1 s Max 60 s Adjust resolution 0.1 s Temperature/speed input min 1 s Max 60 s Adjust resolution 0.1 s Relay logic 1900/65A monitor has six relay outputs that users can open or close contact logic statements according to user-defined programming. The logical statement uses the OK, Alert, and Danger states of any channel or combination of channels as input. Logical operand and bypass channels are ignored, including true and bypass channels or logical operand monitor inhibit monitor unhealthy monitor danger monitor alarm channel abnormal channel danger channel alarm variable danger variable alarm maximum number of 50 relay relay configurations The following configuration options are independent of relay logic, It can be configured for each relay: l Locking or non locking independent of alarm status l Normally energized or normally de energized l Normally open and normally closed contact relay specifications and types
