DEIF DELOMATIC-3控制通信板
參考NTCL01終端裝置或NICL01終端模塊手冊，了解完整的終端設備信息。附錄A和B提供了有關這些終端設備的快速參考信息。用一個NIS模塊安裝一個INICT01 INFI-NET到計算機傳輸模塊（ICT），以形成INICT01-INFI-NET到計算機接口。INICT01模塊由兩塊電路板（一塊內存電路板和一塊CPU電路板）組成。內存板沒有用戶可配置的操作選項。CPU電路板有三個雙列直插式開關，用于設置模塊操作特性。這些雙列直插式開關可選擇模塊操作選項、串行端口通信特性和波特率。圖3-3顯示了CPU電路板上的雙列直插式開關位置。注意：跳線J1至J3為出廠設置。請勿更改跳線設置。雙列直插式開關U72是一個八極雙列直撥式開關，用于確定ICT模塊的操作選項。表3-7列出了雙列直插式開關U72選項設置。在提供的空間中記錄雙列直插式開關U72的設置。1.選擇此選項將自動覆蓋雙列直連式開關位置2和3，并將端口1的數據特性設置為8個數據位、1個停止位和無奇偶校驗位。當未選擇此選項時，雙列直插開關極2和3保持完全功能。2.啟用此選項時，ICT模塊期望來自主機的所有命令將通過實用程序菜單配置的端口地址作為每個命令的第一個字符發送。3.當啟用此選項時，ICT模塊期望來自主機的所有命令包括校驗和字節作為回車前的最后一個字符。ICT模塊在每個答復中都包含一個校驗和
雙列直插式開關U73-串行端口通信速率
雙列直插式開關U73是一個八極雙列直連式開關，用于設置串行端口（RS-233-C）通信速率。通信速率直接影響數據吞吐量。通信速率見表3-8。在提供的空間中記錄雙列直插式開關U73的設置。雙列直插式開關U75啟用計算機接口診斷功能，這些功能僅對合格的貝利控制公司服務人員有意義。必須關閉雙列直插式開關U75上的所有極才能正常工作。表3-9顯示了雙列直插式開關設置。確認雙列直插式開關U75上的所有極均設置為零（閉合或接通）。如果ICT模塊配置正確，即可安裝在模塊安裝單元中。安裝ICT模塊：1.驗證模塊安裝單元中的ICT模塊插槽分配是否與其相關的NIS模塊相鄰。2.驗證在NIS模塊使用的模塊安裝單元插槽和ICT模塊使用的插槽之間的I/O擴展器總線插槽中安裝了24針雙探針。注：安裝帶有ICT模塊的NIS模塊時，NIS模塊和ICT模塊CPU電路板之間必須保持連續性。注意以下事項：a.如果NIS模塊安裝在ICT模塊的左側，則在NIS插槽和ICT插槽之間的I/O擴展器總線插槽中安裝一個雙探針。b、 如果NIS模塊安裝在ICT模塊的右側，則需要進行兩次下探。在NIS插槽和ICT插槽之間安裝一個雙頭探針。在ICT模塊的內存電路板和CPU電路板的插槽之間安裝第二個雙探針。
Refer to the NTCL01 termination unit
or NICL01 termination module manual for complete termination device information. Appendix A and B provide quick reference information about these termination devices.Install one INICT01 INFI-NET to Computer Transfer Module (ICT) with one NIS module to make an INICI01 INFI-NET to Computer Interface.The INICT01 module consists of two circuit boards (a memory circuit board and a CPU circuit board). The memory board has no user-configurable operating options. The CPU circuit board has three dipswitches that set the module operating characteristics. These dipswitches select module operation options, serial port communication characteristics and baud rate. Figure 3-3 shows the dipswitch locations on the CPU circuit board. NOTE: Jumpers J1 through J3 are factory set. Do not change the jumper settings.Dipswitch U72 is an eight pole dipswitch that determines the operating options of the ICT module. Table 3-7 lists the dipswitch U72 option settings. Record the dipswitch U72 settings in the space provided.1. Selecting this option automatically overrides dipswitch positions 2 and 3 and sets port 1 data characteristics to 8 data bits, 1 stop bit, and no parity bit. Dipswitch poles 2 and 3 retain full functionality when this option is not selected. 2. When this option is enabled, the ICT module expects all commands from the host computer to send the port address configured through the utilities menu as the first character of each command. 3. When this option is enabled, the ICT module expects all commands from the host computer to include a checksum byte as the last character before the carriage return. The ICT module includes a checksum in each reply
DIPSWITCH U73 - SERIAL PORT COMMUNICATION RATE
Dipswitch U73 is an eight pole dipswitch that sets the serial port (RS-233-C) communication rate. The communication rate directly affects data throughput. Refer to Table 3-8 for communication rates. Record the dipswitch U73 settings in the space provided.Dipswitch U75 enables computer interface diagnostic functions that are meaningful to qualified Bailey Controls Company service personnel only. All poles on dipswitch U75 must be closed for normal operation. Table 3-9 shows the dipswitch settings. Verify that all poles on dipswitch U75 are set to zero (closed or on).If the ICT module is properly configured, it is ready to be installed in the module mounting unit. To install the ICT module: 1. Verify the ICT module slot assignment in the module mounting unit is adjacent to its associated NIS module.2. Verify that a 24-pin dipshunt is installed in the I/O expander bus sockets between the module mounting unit slot to be used by the NIS module and the slot to be used by the ICT module. NOTE: When installing the NIS module with an ICT module, there must be continuity between the NIS module and the CPU circuit board of the ICT module. Observe the following: a. Install one dipshunt in the I/O expander bus socket between the NIS slot and ICT slot if the NIS module is mounted to the left of the ICT module. b. If the NIS module is mounted to the right of the ICT module, two dipshunts are required. Install one dipshunt between the NIS slot and ICT slot. Install the second dipshunt between the slots of the memory circuit board and the CPU circuit board of the ICT module.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
