產品詳情介紹
HONEYWELL 09472000模擬量控制卡
啟動多個處理器模塊如果連接了包含多個處理器模塊的HIMax系統的電源電壓，則處理器模塊本身將決定首先啟動哪個處理器模塊。系統自動控制啟動順序。如果第一個處理器模塊上的模式開關處于Run（運行）位置，則系統會自動啟動，前提是之前配置了Autostart（自動啟動）。除非其開關位置設置為Init（初始化），否則其余所有處理器模塊都會遵循并啟動系統操作。如果第一個處理器模塊的模式開關處于停止位置，則該處理器模塊采用停止狀態，用戶程序不啟動。所有剩余的處理器模塊遵循并進入STOP狀態，除非其開關位置設置為Init，請參閱第3.4.18章。Init開關位置不會影響其他處理器模塊。i在打開電源電壓之前，將所有處理器模塊的模式開關設置為運行位置，以確保系統能夠安全啟動系統操作。操作模塊在HIMax基板內操作。無需具體監控。5.1處理不可預見直接處理模塊。模塊的用戶程序從PADT內操作，例如啟動或停止。有關更多詳細信息，請參閱SILworX文檔。5.2模塊正面的診斷LED指示模塊狀態，參見第3.4.11章。處理器模塊具有可使用PADT讀取的診斷內存。診斷存儲器最多可存儲1500條短期診斷信息和2500條長期診斷信息。i如果模塊插入基板，它會在初始化階段生成診斷信息，指示錯誤的電壓值等故障。這些消息僅在系統開始運行后出現時表示模塊故障
維護缺陷模塊
必須用相同類型的無故障模塊或經批準的更換型號進行更換。只有制造商有權維修模塊。更換模塊時，請遵守《系統手冊》（HI 801 001 E）和《安全手冊》（HI 801 003 E）中規定的說明。6.1維護措施處理器模塊需要采取以下措施：如果需要新版本，則加載操作系統執行驗證測試6.1.1加載操作系統HIMA正在不斷改進模塊的操作系統。HIMA建議使用系統停機時間將當前版本的操作系統加載到模塊中。有關如何加載操作系統的詳細說明，請參閱系統手冊（HI 801 001 E）和聯機幫助。要加載操作系統，處理器模塊必須處于OutOfRed狀態（以SILworX顯示）。否則，請停止處理器模塊的系統操作。i所用模塊的當前版本顯示在SILworX控制面板中！型號標簽規定了模塊交付時的版本，見第3.3.章HIMax模塊必須每隔10年進行一次驗證測試。有關更多信息，請參閱安全手冊HI 801 003 E。要停用模塊，請將其從底板上拆下。有關更多信息，請參閱安裝和卸下模塊。為避免機械損壞，HIMax組件必須包裝運輸。始終將HIMax組件存儲在其原始產品包裝中。這種包裝還可防止靜電放電。請注意，僅產品包裝不適合運輸。
Starting up Several Processor Modules
If the supply voltage is connected for a HIMax system containing several processor modules, the processor modules themselves determine which processor module will start the first. The system automatically controls the start order. If the mode switch on the first processor module is in the Run position, the system starts automatically, provided that Autostart was previously configured. All remaining processor modules follow and start system operation, unless their switch position is set to is Init. If the mode switch of the first processor module is in the Stop position, this processor module adopts the STOP state and the user program does not start. All remaining processor modules follow and enter the STOP state, unless their switch position is set to Init, see Chapter 3.4.18. The Init switch position does not influence the other processor modules. i Before switching on the supply voltage, set the mode switch of all processor modules to the Run position to ensure that the system can safely start system operation.Operation The module is operated within a HIMax base plate. No specific monitoring is required. 5.1 Handling Direct handling of the module is not foreseen. The module's user program is operated, e.g., started or stopped, from within the PADT. For more details, refer to the SILworX documentation. 5.2 Diagnosis LEDs on the front side of the module indicate the module state, see Chapter 3.4.11. The processor module has a diagnostic memory that can be read using the PADT. The diagnostic memory can store up to 1500 diagnostic messages for the short term diagnosis and 2500 diagnostic messages for the long time diagnosis. i If a module is plugged in to a base plate, it generates diagnostic messages during its initialization phase indicating faults such as incorrect voltage values. These messages only indicate a module fault if they occur after the system starts operation
Maintenance Defective modules
must be replaced with a faultless module of the same type or with an approved replacement model. Only the manufacturer is authorized to repair the module. When replacing modules, observe the instructions specified in the System Manual (HI 801 001 E) and Safety Manual (HI 801 003 E). 6.1 Maintenance Measures The following measures are required for the processor module: ? Loading the operating system, if a new version is required ? Executing the proof test 6.1.1 Loading the Operating System HIMA is continuously improving the operating system of the module. HIMA recommends to use system downtimes to load the current version of the operating system into the module. For detailed instructions on how to load the operating system, see the System Manual (HI 801 001 E) and the online help. For loading the operating system, the processor module must be in the OutOfRed state (displayed in SILworX). Otherwise, stop the system operation of the processor module. i The current version of the module in use is displayed in the SILworX Control Panel! The type label specifies the version when the module is delivered, see Chapter 3.3.HIMax modules must be subjected to a proof test in intervals of 10 years. For more information, refer to the Safety Manual HI 801 003 E.To decommission the module, remove it from the base plate. For more information, see Mounting and Removing the Module.To avoid mechanical damage, HIMax components must be transported in packaging. Always store HIMax components in their original product packaging. This packaging also provides protection against electrostatic discharge. Note that the product packaging alone is not suitable for transport.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
