產品詳情介紹
A-B 80190-560-02-R處理器模塊
安裝處理器模塊時，請注意以下幾點：該模塊用于HIMax基板內。有關底板結構的更多信息，請參閱相應的系統文檔。僅操作目標插槽中的處理器模塊僅使用強制冷卻（X-FAN）操作模塊。只能使用合適的連接器板操作模塊。有關更多信息，請參閱第3.6章卸下和插入模塊的效果：卸下模塊時，連接器板仍保留在HIMax基板中。由于所有外部接口都通過模塊的連接器板連接，因此可以在不影響外部接口的情況下更換模塊。模塊的SRS存儲在連接器板中，并在模塊插入后變為SRS。拔插插頭的效果拔插插頭會中斷外部通信。采取適當的接地措施。注：靜電放電！不遵守這些說明可能會損壞連接器板和/或模塊。確保工作場所無靜電，并佩戴防靜電腕帶。如果未使用，請確保設備免受靜電放電的影響，例如將其存放在包裝中。EMC影響的影響將模塊暴露在手冊中規定以外的環境影響下可能會導致模塊故障甚至損壞。
處理器模塊允許的插槽
將插槽分配給處理器模塊時，以及在硬件編輯器中，必須遵守以下規則：1.最多可以使用四個處理器模塊。2.處理器模塊只能插入以下插槽：-機架0上的插槽3至6。-機架1上的插槽4。3.機架0上插槽5和機架1上插槽4可能不同時包含處理器模塊。4.機架0上槽6和機架1的插槽3可能不同時含有處理器模塊。注：可能存在系統故障！處理器模塊只能使用符合這些規則的插槽。單操作：該項目在SILworX中配置為單操作，在插槽3中只有一個處理器模塊，在插槽1中至少有一個系統總線模塊，I/O模塊和可能的通信模塊。單聲道啟動開關必須設置在SILworX內。這總是可能的（并且是推薦的！）冗余配置系統總線模塊！HIMA建議使用變體3，即使可能使用變體1。這樣，可以在不中斷操作的情況下更換處理器模塊。由于操作系統旨在確保最大可用性，因此可以使用其他組合，但不建議使用。這使得HIMax能夠提供更大的靈活性，例如在更換模塊或修改系統時。然而，在完成這些措施后，系統的結構應符合表17中所述的建議變體之一。
Mounting
Observe the following points when installing the processor module: ? The module is intended for use within a HIMax base plate. For more information on the base plate structure, refer to the corresponding system documentation. ? Only operate processor modules in the intended slots ? Only operate the module with forced cooling (X-FAN). ? Only operate the module with the suitable connector board. For more information, see Chapter 3.6. ? Effects of removing and inserting the module: When removing the module, the connector board remains in the HIMax base plate. Since all of the external interfaces are connected via the module's connector board, a module can be replaced without affecting the external interfaces ? The SRS of the module is stored to the connector board and becomes after the module is plugged in. ? Effects of pulling and plugging the plugs Pulling the plugs interrupts the external communication. Take appropriate grounding measures. NOTE Electrostatic discharge! Failure to comply with these instructions can destroy the connector board and/or the module. ? Make sure that the workspace is free of static and wear an ESD wrist strap. ? If not used, ensure that the device is protected from electrostatic discharge, e.g., by storing it in its packaging.Effects of EMC influences Exposing the module to environmental influences other than those specified in the manual may lead to malfunctions or even the destruction of the module.
Slots Permitted for the Processor Module
The following rules must be observed when assigning the slots to the processor modules, also in the Hardware Editor: 1. A maximum of four processor modules may be used. 2. Processor modules may only be inserted in the following slots: - Slots 3 to 6 on rack 0. - Slots 3 to 4 on rack 1. 3. Slot 5 on Rack 0 and Slot 4 on Rack 1 may not simultaneously contain processor modules.. 4. Slot 6 on Rack 0 and Slot 3 on Rack 1 may not simultaneously contain processor modules.. NOTE System malfunction possible! Only slots complying with these rules may be used for processor modules.Mono operation:The project is configured in SILworX for mono operation and has only one processor module in slot 3, at least one system bus module in slot 1, I/O modules and possibly communication modules. The switch for mono start-up must be set within SILworX. It is always possible (and recommended!) to configure the system bus modules redundantly!HIMA recommends to use variant 3 even if variant 1 would be possible. In doing so, the processor module can be replaced without interrupting operation. Since the operating system is designed to ensure maximum availability, other combinations are possible, but not recommended. This allows HIMax to offer more flexibility, e.g., when replacing modules or modifying the system. However, after such measures have been completed, the system should be structured such that it corresponds to one of the recommended variants noted in Table 17.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
