產品內容介紹
A-B 80190-300-01-R處理器模塊
設置換檔模式-ESC c
QTERM-II上的換擋鍵可以以兩種方式之一操作：?功能模式，其中換擋鍵只移動一次?鎖定模式，其中，換擋鍵保持移動，直到第二次按下。對于任一模式，可以啟用或禁用換擋LED，如果啟用，則可以正確反映換擋鍵的狀態。#的有效值為@-function mode、shift LED enabled A-lock mode、shift LED enable B-function mode、hift LED disabled C-lock module、shift-LED disabled注意，shift LED啟用/禁用不會影響移位操作本身，只會影響LED指示燈。如果您根本不想使用移位鍵，可以通過QDATA文件中的參數禁用移位功能。2.2.40控制數字0和數字1-ESC d#這兩條數字線路可用于一般控制目的，也可用于驅動外部蜂鳴器或喇叭。閃爍模式以QDATA文件中為LED閃爍定義的速率閃爍線路。蜂鳴器模式使線路在內部蜂鳴器打開時接通（高），在內部蜂鳴器關閉時斷開（低）。切換模式使線路的當前狀態反轉。如果該行閃爍并且發送了切換命令，則該行將從當前狀態切換并保持在該狀態（即停止閃爍）。2.2.41設置蜂鳴器持續時間-ESC e#設置“嘟嘟”命令的持續時間。蜂鳴命令可以是鈴聲（07h，^G）或蜂鳴器開/關/蜂鳴命令（ESC O B）。#的有效范圍是41h到7Fh（'A'到DEL）。每個字符設置的持續時間見表1-4。2.2.42設置鍵點擊持續時間-ESC f#設置鍵點擊的長度，實際上是蜂鳴器發出的一聲很短的蜂鳴音。#的有效范圍是41h到7Fh（'A'到DEL）。每個字符設置的持續時間見表1-4。使用鍵單擊/重復模式命令（ESC a）禁用鍵單擊。
設置關鍵幀重復率-ESC g
這將設置密鑰重復率。#的有效范圍是41h到7Fh（'A'到DEL）。每個字符設置的速率見表1-4。請參見“鍵單擊/重復模式”命令（ESC a）以全局禁用鍵重復。使用QDATA文件禁用選定密鑰的密鑰重復。2.2.44設置LED閃爍頻率-ESC h#這將設置LED閃爍速度。#的有效范圍是41h到7Fh（'A'到DEL）。每個代碼設置的速率見表1-4。另請參閱LED開/關/閃爍（ESC P）將參數保存到EEPROM-ESC i此命令會將所有參數存儲到EEPROM。通過軟件命令修改的任何QDATA默認值都將替換為其修改后的值。請注意，QTERM-II中使用的EEPROM具有10000個寫入周期的保證寫入持久性。雖然這遠遠超出了大多數應用程序的要求，但如果您在應用程序中經常使用此命令，則應考慮到這種持久性。2.2.46條形碼控制-ESC j#此命令用于控制條形碼棒（如果安裝了條形碼棒）。條形碼操作對QTERM-II來說基本上是透明的：發送到條形碼棒的命令只在接收時傳輸，從條形碼棒接收的字符直接傳輸到主機。條形碼串行端口不支持握手，這要求主機接口以1200波特或更快的速度運行。#有三個有效值：@-禁用從條形碼棒接收A-啟用從條形碼棒收到B-向條形碼棒發送字符串disable receive from bar code：如果#=“@”，條形碼傳輸到QTERM-II的任何內容都將被忽略。禁止從條碼接收：如果#='A'，條碼傳輸到QTERM-II的任何內容都將傳輸到主機。字節與接收到的字節完全相同，因此主機將接收數據，就像條形碼棒直接發送到主機串行端口一樣
Set Shift Mode - ESC c
The shift key on the QTERM-II can operate in one of two ways: ? FUNCTION MODE, where the shift key stays shifted for one additional key press only ?LOCK MODE, where the shift key stays shifted until it is pressed a second time For either mode, the shift LED can be enabled or disabled, and, if enabled, properly reflects the state of the shift key. Valid values for # are @ - function mode, shift LED enabled A - lock mode, shift LED enabled B - function mode, shift LED disabled C - lock mode, shift LED disabled Note that the shift LED enable/disable does not affect the shift operation itself, only the LED indicator. If you do not wish to have a shift key at all, you can disable the shift function by a parameter in the QDATA file. 2.2.40 Control dig0 and dig1 - ESC d # These two digital lines can be used for general control purposes, or they can be used to drive an external buzzer or horn.The blink mode blinks the line at the rate defined for LED blinking in the QDATA file. The buzzer mode causes the line to go on (high) when the internal buzzer is on, and to go off (low) when the internal buzzer is off. The toggle mode reverses the current state of the line. If the line is blinking and a toggle command is sent, the line will be toggled from its current state and will remain there (i.e. it will stop blinking). 2.2.41 Set Buzzer Duration - ESC e # This sets the duration for a "beep" command. The beep command can either be a Bell (07h, ^G) or the Buzzer On/ Off/Beep command for beep (ESC O B). The valid range for # is 41h through 7Fh ('A' to DEL). See Table 1-4 for the duration set by each character. 2.2.42 Set Key Click Duration - ESC f # This sets the length of the key click, which is actually a very short beep from the buzzer. The valid range for # is 41h through 7Fh ('A' to DEL). See Table 1-4 for the duration set by each character. Use the Key Click/-Repeat Mode command (ESC a) to disable the key click.
Set Key Repeat Rate - ESC g
This sets the key repeat rate. The valid range for # is 41h through 7Fh ('A' to DEL). See Table 1-4 for the rate set by each character. See the Key Click/Repeat Mode command (ESC a) to globally disable key repeats. Use the QDATA file to disable key repeats for selected keys. 2.2.44 Set LED Blink Rate - ESC h # This sets the LED blink rate. The valid range for # is 41h through 7Fh ('A' to DEL). See Table 1-4 for the rate set by each code. See also LEDs On/Off/Blink (ESC P)Save Parameters to EEPROM - ESC i This command causes all parameters to be stored to EEPROM. Any QDATA defaults which have been modified by software commands will be replaced by their modified values. Note that the EEPROM used in the QTERM-II has a guaranteed write endurance of 10,000 write cycles. Although this is far more than most applications will ever require, if you use this command frequently in your application, you should take this endurance into consideration. 2.2.46 Bar Code Control - ESC j # This command is used to control a bar code wand (if one is installed). The bar code operation is mostly transparent to the QTERM-II: commands sent to the bar code wand are simply transmitted as received, and characters received from the bar code wand are transmitted directly to the host. The bar code serial port does not support handshaking, which requires that the host interface run at 1200 baud or faster. There are three valid values for #: @ - disable receive from bar code wand A - enable receive from bar code wand B - transmit a string to the bar code wand DISABLE RECEIVE FROM BAR CODE: if # = '@,' anything which the bar code transmits to the QTERM-II will be ignored.NABLE RECEIVE FROM BAR CODE: if # = 'A,' anything which the bar code transmits to the QTERM-II will be transmitted to the host. Bytes are transmitted exactly as received, so the host will receive the data as if the bar code wand were transmitting directly to the host serial port
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
