產品內容介紹
REXROTH BTV30.2PA-24R-55C-D-NW驅動器
瞬時剩余過電流保護EFPIOC具有較低的瞬時過電流和較短的跳閘時間，以允許使用瞬時接地故障保護，其范圍限制在最小電源阻抗下線路的典型80%以下。EFPIOC可配置為測量三相電流輸入的剩余電流或單獨電流輸入的電流。通過激活輸入BLOCK可以阻止EFPIOC。四步剩余電流保護、零序和負序方向EF4PTOC。四步剩余過電流保護EF4PTOC具有獨立于每個步驟的反時限或定時限延時。所有IEC和ANSI延時特性以及可選的用戶定義特性都可用。對于每個步驟，EF4PTOC可以單獨設置為定向或非定向。IDir、UPol和IPol可以獨立選擇為零序或負序。每一步可單獨設置二次諧波閉鎖。EF4PTOC可用作相對地故障的主保護。EF4PTOC還可用于提供系統備份，例如，在一次保護因通信或電壓互感器電路故障而停用的情況下。在允許或閉鎖遠程保護方案中，定向操作可以與相應的通信邏輯結合在一起。電流反向和弱端饋電功能也可用。EF4PTOC可配置為測量來自三相電流輸入的剩余電流或來自單獨電流輸入的電流。可為該功能設置二次諧波閉鎖電平，并可用于單獨閉鎖每個步驟
四步負序過流保護
NS4PTOC四步負序過電流保護（NS4PTOC）具有獨立于每一步的反時限或定時限延時。所有IEC和ANSI延時特性以及可選的用戶定義特性都可用。定向功能為電壓極化或雙極化。對于每個步驟，NS4PTOC可以單獨設置為定向或非定向。NS4PTOC可作為不對稱故障的主保護；相間短路、相間接地短路和單相接地故障。NS4PTOC還可用于提供系統備份，例如，在一次保護因通信或電壓互感器電路故障而停用的情況下。在允許或閉鎖遠程保護方案中，定向操作可以與相應的通信邏輯結合在一起?？梢允褂门c定向零序電流相同的邏輯。電流反轉和弱化饋電功能可用。靈敏方向剩余電流和功率保護SDEPSDE在隔離網絡或高阻抗接地網絡中，接地故障電流明顯小于短路電流。除此之外，故障電流的大小幾乎與網絡中的故障位置無關。保護裝置可以選擇使用剩余電流或剩余功率元件3U0·3I0·cos j，用于維持短路容量的運行量。還有一個非定向3I0步驟和一個3U0過壓跳閘步驟。不需要特定的靈敏電流輸入。SDEPSDE可以設置為IBase的0.25%。
Instantaneous residual overcurrent protection EFPIOC
The Instantaneous residual overcurrent protection EFPIOC has a low transient overreach and short tripping times to allow the use for instantaneous earth-fault protection, with the reach limited to less than the typical eighty percent of the line at minimum source impedance. EFPIOC can be configured to measure the residual current from the three-phase current inputs or the current from a separate current input. EFPIOC can be blocked by activating the input BLOCK. Four step residual overcurrent protection, zero sequence and negative sequence direction EF4PTOC The four step residual overcurrent protection EF4PTOC has an inverse or definite time delay independent for each step separately. All IEC and ANSI time-delayed characteristics are available together with an optional user defined characteristic. EF4PTOC can be set directional or non-directional independently for each of the steps. IDir, UPol and IPol can be independently selected to be either zero sequence or negative sequence. Second harmonic blocking can be set individually for each step. EF4PTOC can be used as main protection for phase-to-earth faults. EF4PTOC can also be used to provide a system back-up for example, in the case of the primary protection being out of service due to communication or voltage transformer circuit failure. Directional operation can be combined together with corresponding communication logic in permissive or blocking teleprotection scheme. Current reversal and weak-end infeed functionality are available as well. EF4PTOC can be configured to measure the residual current from the three-phase current inputs or the current from a separate current input.Second harmonic blocking level can be set for the function and can be used to block each step individually
Four step negative sequence overcurrent protection
NS4PTOC Four step negative sequence overcurrent protection (NS4PTOC) has an inverse or definite time delay independent for each step separately. All IEC and ANSI time delayed characteristics are available together with an optional user defined characteristic. The directional function is voltage polarized or dual polarized. NS4PTOC can be set directional or non-directional independently for each of the steps. NS4PTOC can be used as main protection for unsymmetrical fault; phase-phase short circuits, phase-phase-earth short circuits and single phase earth faults. NS4PTOC can also be used to provide a system back-up for example, in the case of the primary protection being out of service due to communication or voltage transformer circuit failure. Directional operation can be combined together with corresponding communication logic in permissive or blocking teleprotection scheme. The same logic as for directional zero sequence current can be used. Current reversal and weakend infeed functionality are available. Sensitive directional residual overcurrent and power protection SDEPSDE In isolated networks or in networks with high impedance earthing, the earth fault current is significantly smaller than the short circuit currents. In addition to this, the magnitude of the fault current is almost independent on the fault location in the network. The protection can be selected to use either the residual current or residual power component 3U0·3I0·cos j, for operating quantity with maintained short circuit capacity. There is also available one nondirectional 3I0 step and one 3U0 overvoltage tripping step. No specific sensitive current input is needed.SDEPSDE can be set as low 0.25% of IBase.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
