產品內容介紹
1775-MEA/B運行64K存儲器
串行接口COM2規格簡介注：有關如何連接控制器和其他類型設備的信息，請參閱屏幕編輯軟件的相應設備驅動程序手冊。串行端口未隔離。SG（信號接地）和FG（機架接地）端子連接在面板內。串行接口COM2 HMIGTO2300/HMIGTO2310/HMIGTO 2315：通過RS-485電纜的RJ45連接器。注：設置RS-485通信時，某些設備的電纜圖可能需要在終端側極化。此終端不需要任何特殊設置，因為它可以自動處理極化。當使用SG終端將外部設備連接到面板時：? 設置系統時，請確認沒有創建短路回路。? 當主機（PLC）單元未隔離時，將#8 SG終端連接到遠程設備。將#8 SG端子連接至已知可靠的接地連接，以降低損壞電路的風險。不遵守這些說明將導致死亡或重傷。有關如何連接控制器和其他類型設備的信息，請參閱屏幕編輯軟件的相應設備驅動程序手冊。? 通信端口的所有連接不得對端口施加過大壓力。? 將通信電纜牢牢連接到面板或機柜。? 僅使用狀態良好的鎖定系統的D-Sub 9針電纜。
HMIGTO的正面
安裝在實心面板中，已使用與規范中所示標準等效的條件進行測試。盡管HMIGTO的阻力水平與這些標準相當，但對HMIGTO沒有影響的油可能會損害面板。這可能發生在存在汽化油的區域，或允許低粘度切削油長時間粘附在面板上的區域。如果面板正面保護板脫落，這些情況可能導致油進入面板，建議采取單獨的保護措施。此外，如果存在未經批準的機油，它們可能會導致前面板塑料罩變形或腐蝕。因此，在安裝HMIGTO之前，確保確認面板操作環境中存在的條件類型。如果長期使用安裝墊片，或者從面板上拆下HMIGTO及其墊片，則無法保持原有的防護等級。為了保持原有的保護水平，請確保定期更換安裝墊片*2對于尺寸公差，所有+1/-0 mm（+0.04/-0 in）和R（角度）均低于R3（R0.12 in）*3即使安裝壁厚在“面板切割尺寸”的建議范圍內，取決于壁的材料、尺寸和面板和其他設備的安裝位置，安裝壁也可能翹曲。為了防止翹曲，可能需要加強安裝表面。根據面板的工作溫度和使用年限，時鐘可以從-380秒/月偏離到+90秒/月。對于這種精度水平不足的系統，用戶應進行監控，并在需要時進行調整。
Specifications of Serial Interface COM2
Introduction NOTE: For information on how to connect controllers and other types of equipment, refer to the corresponding device driver manual of your screen editing software. The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected inside the panel. Serial Interface COM2 HMIGTO2300 / HMIGTO2310 / HMIGTO2315: RJ45 connector via a RS-485 cable. NOTE: When setting up RS-485 communication, the cable diagram for some equipment may require polarization on the terminal side. This terminal does not require any special setting as it handles polarization automatically When using the SG terminal to connect an external device to the panel: ? Verify that a short-circuit loop is not created when you set up the system. ? Connect the #8 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect the #8 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit. Failure to follow these instructions will result in death or serious injury.For information on how to connect controllers and other types of equipment, refer to the corresponding device driver manual of your screen editing software.? All connections to the communication ports must not put excessive stress on the ports. ? Securely attach communication cables to the panel or cabinet. ? Use only D-Sub 9-pin cables with a locking system in good condition.
The front face of the HMIGTO
installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the HMIGTO's level of resistance is equivalent to these standards, oils that should have no effect on the HMIGTO can possibly harm the panel. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the panel for long periods of time. If the panel's front face protection sheet peels off, these conditions can lead to the ingress of oil into the panel and separate protection measures are suggested. Also, if non-approved oils are present, they may cause deformation or corrosion of the front panel’s plastic cover. Therefore, prior to installing the HMIGTO, be sure to confirm the type of conditions that will be present in the panel’s operating environment. If the installation gasket is used for a long period of time, or if the HMIGTO and its gasket are removed from the panel, the original level of protection cannot be kept. To maintain the original protection level, be sure to replace the installation gasket regularly. *2 For dimensional tolerance, everything +1/-0 mm (+0.04/-0 in) and R in angle are below R3 (R0.12 in) *3 Even if the installation wall thickness is within the recommended range for the “Panel Cut Dimensions”, depending on wall’s material, size, and installation location of the panel and other devices, the installation wall could warp. To prevent warping, the installation surface may need to be strengthened.Depending on the operating temperature and age of panel, the clock can deviate from -380 to +90 sec/month. For systems where this level of precision is insufficient, the user should monitor and make adjustments when required.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
