產品內容介紹
1326AB-B430E-M2K4LS控制速度模塊
結構規范安裝在實心面板中的HMIGTO的正面已經使用與規范中所示標準等效的條件進行了測試。盡管HMIGTO的阻力水平與這些標準相當，但對HMIGTO沒有影響的油可能會損害面板。這可能發生在存在汽化油的區域，或允許低粘度切削油長時間粘附在面板上的區域。如果面板正面保護板脫落，這些情況可能導致油進入面板，建議采取單獨的保護措施。此外，如果存在未經批準的機油，它們可能會導致前面板塑料罩變形或腐蝕。因此，在安裝面板之前，請確保確認面板操作環境中存在的條件類型。如果長期使用安裝墊片，或者如果面板及其墊片從面板上拆下，則無法保持原有的防護等級。為了保持原有的保護水平，請確保定期更換安裝墊片*2在面板中安裝HMIGTO時，可能無法將HMIGTO與面板平齊安裝。這是由于墊片的厚度造成的。HMIGTO和面板之間的液位差取決于墊片被壓縮的程度。HMIGTO2315*3的電路板上有保形涂層。對于尺寸公差，所有+1/-0 mm（+0.04/-0 in）和R的角度均低于R3（R0.12 in）*4即使安裝壁厚在“面板切割尺寸”的建議范圍內，取決于墻的材料、尺寸和面板和其他設備的安裝位置，安裝壁也可能翹曲。為了防止翹曲，可能需要加強安裝表面。
內存、時鐘和觸摸面板
簡介注釋：? 當HMIGTO2300上顯示指示電池電量低的消息時，向面板供電并給電池充滿電。24小時內，電池充電至允許備用操作的水平。完成完全充電需要大約120小時（五天）。? 鋰電池的壽命為：電池環境溫度為40°C（104°F）或以下時為10年，電池環境溫度在50°C（122°F）及以下時為4.1年，電池的環境溫度在60°C（140°F）以下時為1.5年。用于備份時：? 電池充滿電約100天。? 使用半充電電池約6天。? 當HMIGTO2310/2315上顯示指示電池電量低的消息時，請更換電池（參見第134頁）*1根據面板的工作溫度和使用年限，時鐘可能會從-380秒/月偏離至+90秒/月。對于這種精度水平不足的系統，用戶應進行監控，并在需要時進行調整。有關如何連接控制器和其他類型設備的信息，請參閱屏幕編輯軟件的相應設備驅動程序手冊。使用SG端子將外部設備連接到面板時：? 設置系統時，請確認沒有創建短路回路。? 當主機（PLC）單元未隔離時，將#5 SG終端連接到遠程設備。將#5 SG端子連接至已知可靠的接地連接，以降低損壞電路的風險。串行端口未隔離。SG（信號接地）和FG（機架接地）端子連接在面板內。
Structural Specifications
The front face of the HMIGTO, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the HMIGTO's level of resistance is equivalent to these standards, oils that should have no effect on the HMIGTO can possibly harm the panel. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the panel for long periods of time. If the panel's front face protection sheet peels off, these conditions can lead to the ingress of oil into the panel and separate protection measures are suggested. Also, if non-approved oils are present, they may cause deformation or corrosion of the front panel’s plastic cover. Therefore, prior to installing the panel, be sure to confirm the type of conditions that will be present in the panel’s operating environment. If the installation gasket is used for a long period of time, or if the panel and its gasket are removed from the panel, the original level of protection cannot be kept. To maintain the original protection level, be sure to replace the installation gasket regularly. *2 When installing the HMIGTO in a panel, you may not be able to mount the HMIGTO flush with the panel. This occurs due to the thickness of the gasket. The difference in level between the HMIGTO and panel depends on how much the gasket is compressed. There is a conformal coating on circuit boards for HMIGTO2315 *3 For dimensional tolerance, everything +1/-0 mm (+0.04/-0 in) and R in angle are below R3 (R0.12 in). *4 Even if the installation wall thickness is within the recommended range for the “Panel Cut Dimensions”, depending on wall's material, size, and installation location of the panel and other devices, the installation wall could warp. To prevent warping, the installation surface may need to be strengthened.
Memory, Clock, and Touch Panel
Introduction NOTE: ? When the message indicating that the battery level is low is displayed, on the HMIGTO2300, supply power to the panel and fully charge the battery. In 24 hours the battery charges to a level that allows backup operation. Completing a full charge requires about 120 hours (five days). ? The lithium battery's lifetime is: 10 years when the battery's ambient temperature is 40 °C (104 °F) or less, 4.1 years when the battery's ambient temperature is 50 °C (122 °F) or less, and 1.5 years when the battery's ambient temperature is 60 °C (140 °F) or less. When used for backup: ? Approximately 100 days with a fully charged battery. ? Approximately 6 days with a half-charged battery. ? When the message indicating that the battery level is low is displayed on HMIGTO2310/2315, replace the battery (see page 134) *1 Depending on the operating temperature and age of panel, the clock can deviate from -380 to +90 sec/month. For systems where this level of precision is insufficient, the user should monitor and make adjustments when required.For information on how to connect controllers and other types of equipment, refer to the corresponding device driver manual of your screen editing software.When using the SG terminal to connect an external device to the panel: ? Verify that a short-circuit loop is not created when you set up the system. ? Connect the #5 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect the #5 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit.The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected inside the panel.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
