產品內容介紹
1398-DDM-150X擴展數字模塊
EMC指令的適用標準表A3.1和A3.2給出了適用于FA-M3的標準，說明符合CE標志的模塊滿足表中所示的規定值和性能標準。有關符合CE標記的模塊的詳細信息，請參閱“標準批準和符合FA-M3模塊列表”（GS 34M06C11-21E）。從低壓指令的安全觀點來看，有必要在面板外殼內安裝和使用設備。EMC指令一致性測試是在安裝在通用面板外殼中的設備上進行的。測試期間使用的面板外殼具有發射短閃爍指數：Pst<1長閃爍指數：P lt<0.65相對穩定電壓波動：dc<3.3%最大相對電壓波動：dmax<4%電壓波動時間：電壓波動超過3.3%的時間應小于平均15dB和最大25dB（從30到1000 MHz）的噪聲衰減特性500ms。以下標準用于確定是否符合標準：性能標準a：設備繼續按照規范運行。性能標準B：性能暫時下降，但在噪聲消失后，設備仍按規范運行。性能標準C：存在可通過自恢復功能或操作員干預恢復的臨時故障。性能標準D：設備損壞導致的不可恢復故障。
安裝注意事項
從低壓指令的安全觀點來看，該設備應安裝在面板外殼內。從EMC的角度來看，使用金屬面板外殼可以實現屏蔽效果。EMC指令一致性測試是對安裝在通用面板外殼內的設備進行的。測試期間使用的面板外殼具有平均15dB和最大25dB（從30到1000MHz）的輻射噪聲衰減特性。安裝FA-M3時應注意的事項總結如下。圖A3.37以圖形方式對此進行了說明使用金屬面板外殼和金屬板安裝設備使用編織線或其他電線將面板外殼和金屬板接地，以確保即使在高頻下也具有低阻抗將屏蔽電纜用于從面板外殼引出的信號電纜使用螺釘將該設備的基礎模塊直接固定在金屬板上短接本設備電源模塊的FG端子和LG端子，并用盡可能短的接線將其連接至金屬板在對面板外殼的金屬板進行涂層時，遮蓋以下零件并露出金屬表面，以確保導電性將FA-M3安裝到面板外殼的螺栓-與基礎模塊鋁制底盤的接觸面-與電源模塊FG和LG端子接線的連接屏蔽電纜FG夾具的位置。
Applicable Standards of the EMC Directive
The standards applicable to the FA-M3 are given in tables A3.1 and A3.2 Modules declaring conformity to the CE Mark satisfy the specified values and performance criteria displayed in the tables. For details on modules conforming to the CE Marking, see “List of Standard-Approved and Compliant FA-M3 Modules.” (GS 34M06C11-21E) From the safety viewpoint of the Low Voltage directive, it is necessary to install and use the equipment within a panel enclosure. The EMC directive conformance test is conducted with the equipment installed in a general panel enclosure. The panel enclosure used during the test has an emissiShort flicker index: Pst < 1 Long flicker index: Plt < 0.65 Relative steady voltage fluctuation: dc < 3.3% Maximum relative voltage fluctuation: dmax < 4% Voltage fluctuation time: time where voltage fluctuations exceeds 3.3% should be less than 500msve noise attenuation characteristic of 15dB average and 25dB maximum (from 30 to 1000 MHz).The following criteria are used to determine conformity to a standard: Performance criterion A: The equipment continues to operate according to specification. Performance criterion B: There is a temporary drop in performance but the equipment continues to operate according to specification after the noise disappears. Performance criterion C: There is a temporary failure which can be recovered by the self-recovery function or by operator intervention. Performance criterion D: Non-recoverable failure due to equipment damage.
Installation Considerations
From the safety viewpoint of the Low Voltage directive, this equipment should be installed within a panel enclosure. Using a metallic panel enclosure achieves the shield effect from the EMC viewpoint. The EMC directive conformance test is conducted with the equipment installed within a general panel enclosure. The panel enclosure used during the test has an emissive noise attenuation characteristic of 15dB average and 25dB maximum (from 30 to 1000MHz). The considerations that should be observed when installing the FA-M3 are summarized below. Figure A3.37 illustrates this graphically. - Use a metallic panel enclosure and metal plate to install the equipment. - Ground the panel enclosure and metal plate using braided or other wires to ensure low impedance even at high frequencies. - Use shielded cables for signal cables leading out of the panel enclosure. - Secure the base module of this equipment directly onto the metal plate using screws. - Short the FG terminal and the LG terminal of the power supply module of this equipment and connect it to the metal plate with the shortest wiring possible. - When coating the metal plate of the panel enclosure, mask the following parts and expose the metallic surface to ensure electrical conductance. - the bolts that mounts the FA-M3 to the panel enclosure - The contact surface to the aluminum chassis of the base module - The connection to the wiring to the FG and LG terminals of the power supply module. - The location of the FG clamp for the shielded cable.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
