產品內容介紹
Schumacher 1491-1500N SCN數字流量控制器
NTAC-01兼容ACS 600驅動器的標準應用程序版本為2.8至3.0。5.0版（及更高版本）需要使用NTAC-02。因此，NTAC-01和NTAC-02.不可互換。NTAC-01和NTAC-02之間的差異本手冊其他地方給出的有關NTAC-01的所有信息也適用于NTAC-01.本節中列出的內容除外。端子名稱NTAC-01的端子可以按照第3章中的NTAC-02所示進行連接。雖然標簽上沒有標記，但NTAC-01端子X(jué)2:1實際上可以用作額外的-V端子。此外，SH和PE端子均連接至模塊接地。編碼器電源電壓NTAC-01提供的編碼器電源電壓為12和24 V（而不是NTAC-02提供的15和24 V）。布線NTAC-01的最大編碼器電纜長度為150米。技術數據編碼器輸入：?邏輯閾值（12伏編碼器電源）：“1”>8.3伏，“0”<3.7伏標準應用程序V2.8至3.0中的NTAC設置。本節僅適用于將NTAC-01模塊連接到配備標準應用程序版本2.8至3.0的ACS 600時。其他應用程序的用戶應參考驅動手冊。在調整參數之前，請確保模塊節點號設置為16。請注意，該設置僅在以下模塊通電時生效。
編碼器模塊
此參數激活A(yù)CS 600和NTAC模塊之間的通信。是通信處于活動狀態。NO Communication（無通信）未激活。組50中的參數定義編碼器信號解碼和ACS 600在編碼器或NTAC模塊故障條件下的操作。只有在ACS 600和NTAC模塊之間的通信被參數98.1.50.1 PULSE NR激活后，這些參數才可用。該參數設置每轉編碼器脈沖數。128…4096 50.2速度測量模式此參數定義如何計算編碼器脈沖。此參數定義ACS 600在脈沖編碼器和NTAC模塊之間或NTAC模塊和ACS 600之間的通信丟失時的操作。警告控制面板上顯示警告指示。故障控制面板上顯示故障指示，ACS 600停止電機。50.4編碼器延遲此參數定義了在ACS 600采取參數50.3選擇的操作之前，通信可能會丟失的時間（毫秒）。NDIO-01和NDIO-02之間的差異本手冊其他地方給出的所有關于NDIO-01的信息也適用于NDIO-01.本節所列內容除外。在NDIO-01上設置模塊節點號時，7路DIP開關僅用于地址設置（即，NDIO 01沒有NDIO 02中的硬件過濾器抑制功能）。此外，開關執行器位置“ON”對應于“0”。
The NTAC-01 is compatible
with ACS 600 drives with Standard Application Program versions from 2.8 to 3.0. Version 5.0 (and later) require the use of the NTAC-02. Thus, NTAC-01 and NTAC-02 are not interchangeable. Differences between NTAC-01 and NTAC-02 All information about the NTAC-02 given elsewhere in this manual also applies to the NTAC-01, with the exception of what is listed in this section. Terminal Designations The terminals of the NTAC-01 can be connected as shown for the NTAC-02 in Chapter 3. Although unmarked on the label, NTAC-01 terminal X2:1 can actually be used as an additional -V terminal. Moreover, the SH and PE terminals are both connected to module earth. Encoder Supply Voltage The encoder supply voltages available from the NTAC-01 are 12 and 24 V (instead of 15 and 24 V available with the NTAC-02). Cabling The maximum encoder cable length for the NTAC-01 is 150 m. Technical Data Encoder inputs: ? Logical thresholds (12 V encoder supply): “1” > 8.3 V, “0” < 3.7 V NTAC Setup in Std. Application Program V2.8 to 3.0 This section only applies when an NTAC-01 module is connected to an ACS 600 equipped with Standard Application Program version 2.8 to 3.0. Users of other application programs should refer to the drive manuals. Before adjusting the parameters, ensure that the module node number is set to 16. Note that the setting takes effect only on the following module power-up.
ENCODER MODULE
This parameter activates the communication between the ACS 600 and the NTAC module. YES Communication is active. NO Communication is not active.The parameters in Group 50 define the encoder signal decoding and the operation of the ACS 600 in encoder or NTAC module fault conditions. These parameters are available only after the communication between the ACS 600 and the NTAC module is activated with Parameter 98.1. 50.1 PULSE NR This parameter sets the number of encoder pulses per one revolution. 128 … 4096 50.2 SPEED MEAS MODE This parameter defines how the encoder pulses are calculated.This parameter defines the operation of the ACS 600 upon a communication loss between the pulse encoder and the NTAC module, or between the NTAC module and the ACS 600. WARNING A Warning indication is displayed on the control panel. FAULT A Fault indication is displayed on the control panel and the ACS 600 stops the motor. 50.4 ENCODER DELAY This parameter defines the time (in milliseconds) for which communication may be lost until the ACS 600 takes the action selected with Parameter 50.3.Differences between NDIO-01 and NDIO-02 All information about the NDIO-02 given elsewhere in this manual also applies to the NDIO-01, with the exception of what is listed in this section. Setting the Module Node Number On the NDIO-01, the 7-way DIP switch is used for address setting only (i.e., the NDIO-01 does not have the hardware filter suppression feature found in the NDIO-02). Moreover, switch actuator position “ON” corresponds to “0”.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
