產品內容介紹
XYCOM 9487-47B1319210000連接控制終端
4.02版驅動器AOP需要用戶操作才能啟用ADC。這有助于驗證用戶在打開ADC之前了解ADC操作。請注意使用4.02版（或更高版本）驅動器AOP時，ADC工作狀態如下：
?添加新驅動器時，對于任何支持ADC，例如固件為7.001或更高版本的PowerFlex 753驅動器，或固件為4.001或更高版本的PowerFlex 755驅動器。
?將早期的RSLogix 5000項目轉換為版本20.00時已使用4.02（或更高版本）Drive AOP或更新使用4.01版驅動器AOP創建的項目時，任何ADC對于支持ADC的驅動器，設置將按原樣傳遞。對于例子：
–如果在以前的項目中對某個驅動器禁用了ADC，它將保留殘廢
–如果使用4.01版驅動器AOP的驅動器啟用了ADC，并且項目后來更新到4.02（或更高版本）Drive AOP，它將保持啟用狀態。
通過相應的端口屬性對話框管理外圍設備的鍵控每個外圍設備的框。
嵌入式EtherNet/IP適配器的電子鍵控（僅端口13PowerFlex 755驅動器上）和DeviceLogix（端口14）端口被“禁用”默認情況下。
兩個端口都沒有單獨的固件，目前由驅動器固件（端口0）管理。如果將其中之一設置為“完全匹配”，固件主管將無法找到升級安裝過程中的文件。如果“外圍設備驅動連接故障”復選框被選中，并且在連接到時出現不匹配或故障或者配置這兩個端口，整個ADC進程將失敗將與驅動器進行I/O連接。
HIM和串行轉換器（1203-SSS和1203）的電子鑰匙-USB）默認禁用。
這些通常是臨時設備或僅用于監控目的，因此，如果是否存在。
您仍然可以選擇將這些設置為其他鍵控選擇（如果需要）。兼容模塊此選擇是不使用固件管理器時的典型ADC選擇。
A.更換驅動器（包括外圍設備）需要具有相同或更高的固件版本與原始版本相同。由于需要更新固件的驅動器與舊固件兼容，這允許ADC在不兼容的情況下工作關注點。請注意，如果系列更改伴隨著主要固件更改，則替換驅動器可能與鍵控“兼容”，也可能不兼容。
禁用使用ADC時，通常不應使用此選項。此選擇允許更換驅動器以具有任何不同的主（X.xxx）和/或次（X.xx）固件修訂由用戶提供具有固件版本的更換件晚于或等于原始驅動器。如果更換驅動器的固件較舊則ADC下載可能失敗。
Version 4.02 Drive AOPs require user action to enable ADC.
This helps verify that the user understands ADC operation prior to turning it on. Note the following ADC operating status when using version 4.02 (or later) Drive AOPs: ? When adding a new drive, ADC is disabled by default for any drive that supports ADC, such as PowerFlex 753 drives with firmware 7.001 or later, or PowerFlex 755 drives with firmware 4.001 or later. ? When converting an earlier RSLogix 5000 project to a version 20.00 project that has been updated with version 4.02 (or later) Drive AOPs or when updating a project created with version 4.01 Drive AOPs, any ADC settings will be passed through as-is for drives that support ADC. For example: – If ADC was disabled for a drive in a previous project, it will remain disabled. – If ADC was enabled for a drive using version 4.01 Drive AOPs and that project was later updated to version 4.02 (or later) Drive AOPs, it will remain enabled.Keying for peripherals is managed via the respective Port Properties dialog box for each peripheral.
Electronic Keying for the embedded
EtherNet/IP adapter (only Port 13 on PowerFlex 755 drives) and DeviceLogix (Port 14) ports are “Disabled” by default. Both ports do not have individual firmware and are currently managed by the drive’s firmware (Port 0). If you set either of these to “Exact Match,” Firmware Supervisor will be unable to locate the upgrade files during setup. If the “Fault Drive Connection on Peripheral Error” checkbox is selected and there is a mismatch or failure while connecting to or configuring these two ports, the overall ADC process will fail and no I/O connection will be made to the drive. Electronic Keying for HIMs and serial converters (1203-SSS and 1203- USB) are disabled by default. These are typically temporary devices or used for monitoring purposes only and therefore “do not matter” if they are present or not. You still have the option to select these to other Keying selections if desired.
Compatible Module
This selection is the typical ADC selection when Firmware Supervisor is not used. A replacement drive (including peripherals) will need to have the same or higher firmware revision as the original. Since drives with newer firmware are required to be compatible with older firmware, this allows ADC to work without compatibility concerns. Note that if a Series change accompanies a Major firmware change, the replacement drive may or may not be “compatible” with respect to keying. Disabled When using ADC, this selection should generally not be used. This selection allows a replacement drive to have any different Major (X.xxx) and/or Minor (X.xxx) firmware revision. It is up to the user to provide a replacement that has a firmware revision later than or equal to the original drive. If a replacement drive with older firmware is used, the ADC download may fail.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
