產品內容介紹
FOXBORO 57625-441連接終端顯示
存在受傷或設備損壞的風險。主機參數35-[Peer Flt Action]允許您確定選項模塊的操作如果選項模塊無法與指定的對等方。默認情況下，此參數會導致驅動器故障。
您可以配置此參數使驅動器繼續運行，但應采取預防措施用于驗證此參數的設置不會產生危險受傷或設備損壞。調試驅動器時，請確認系統正確響應各種情況（例如，斷開連接電纜）。如果發送邏輯命令，請使用設備參數30-[Logic SrcCfg]設置包含邏輯命令的數據鏈路的編號在設備參數28-[DLs Fr Peer Cfg]定義的范圍內。
例如，如果設備參數28-[DLs Fr Peer Cfg]設置為接收
五條數據鏈路（數據鏈路12至16）以及這五條數據鏈中的第一條Datalinks（Datalink 12）包含邏輯命令，設置設備參數30-[Logic Src Cfg]設置為值“1”。否則，設置參數30到值“0”。邏輯命令位定義見附錄D或驅動器文檔。
8.如果發送參考，使用設備參數31-[Ref Src Cfg]設置包含范圍內引用的Datalink的編號由設備參數28-[DLs Fr Peer Cfg]定義。
例如，如果設備參數28-[DLs Fr Peer Cfg]設置為接收五條數據鏈路（數據鏈路12至16）和這五條中的第二條Datalinks（Datalink 13）包含參考，設置設備參數31-[Ref Src Cfg]設置為值“2”。否則，將參數31設置為值“0.”
9.在每個PowerFlex 750系列從屬驅動器中，設置驅動器參數308-[方向模式]至“0”（單極），以確保它確遵循主驅動器的速度基準和指令方向。
設置故障操作（僅適用于適配器模式）默認情況下，當通信中斷時（例如，網絡電纜斷開連接），控制器處于空閑狀態（處于程序模式或出現故障），和/或對等I/O或者驅動控制的明確消息被中斷，如果發生以下情況，驅動將以故障響應它正在使用來自網絡的I/O。
您可以配置不同的響應事件：
?使用主機參數33-[Comm Flt中斷I/O通信操作]。
?使用主機參數34-[idle Flt Action]的空閑控制器。
?使用主機參數35-[peer Flt Action]中斷對等I/O。
?通過PCCC、CIP中斷驅動器控制的明確消息使用主機參數36注冊對象或CIP程序集對象-[消息Flt操作]。
分別讓您確定選項模塊的操作如果通信中斷，控制器處于空閑狀態，對等I/O或驅動器控制的明確消息被中斷。默認情況下，這些參數故障驅動器。
您可以配置這些參數，以便驅動器但是，應采取預防措施來驗證設置這些參數中的任何一個都不會造成人身傷害或設備損壞的風險。
什么時候調試驅動器，驗證您的系統是否正確響應各種情況（例如，斷開的網絡電纜、處于空閑狀態的控制器或明確的消息控制中斷）。
Risk of injury or equipment damage exists.
Host Parameter 35 - [Peer Flt Action] lets you determine the action of the option module and connected drive if the option module is unable to communicate with the designated peer. By default, this parameter faults the drive. You may configure this parameter so that the drive continues to run, however, precautions should be taken to verify that the setting of this parameter does not create a hazard of injury or equipment damage. When commissioning the drive, verify that your system responds correctly to various situations (for example, a disconnected cable).If a Logic Command is being sent, use Device Parameter 30 - [Logic Src Cfg] to set the number of the Datalink that contains the Logic Command within the range defined by Device Parameter 28 - [DLs Fr Peer Cfg]. For example, if Device Parameter 28 - [DLs Fr Peer Cfg] is set to receive five Datalinks (Datalinks 12 through 16) and the first of those five Datalinks (Datalink 12) contains the Logic Command, set Device Parameter 30 - [Logic Src Cfg] to a value of “1.” Otherwise, set Parameter 30 to a value of “0.” For Logic Command bit definitions, see Appendix D or the drive documentation. 8. If a Reference is being sent, use Device Parameter 31 - [Ref Src Cfg] to set the number of the Datalink that contains the Reference within the range defined by Device Parameter 28 - [DLs Fr Peer Cfg]. For example, if Device Parameter 28 - [DLs Fr Peer Cfg] is set to receive five Datalinks (Datalinks 12 through 16) and the second of those five Datalinks (Datalink 13) contains the Reference, set Device Parameter 31 - [Ref Src Cfg] to a value of “2.” Otherwise, set Parameter 31 to a value of “0.” 9. In each PowerFlex 750-Series slave drive, set drive parameter 308 - [Direction Mode] to “0” (Unipolar) to be sure that it properly follows the master drive’s speed reference and commanded direction.
Setting a Fault Action (Adapter mode only)
By default, when communication is disrupted (for example, the network cable is disconnected), the controller is idle (in program mode or faulted), and/or peer I/O or explicit messaging for drive control is disrupted, the drive responds by faulting if it is using I/O from the network. You can configure a different response to these events: ? Disrupted I/O communication by using Host Parameter 33 - [Comm Flt Action]. ? An idle controller by using Host Parameter 34 - [Idle Flt Action]. ? Disrupted peer I/O by using Host Parameter 35 - [Peer Flt Action]. ? Disrupted explicit messaging for drive control via PCCC, the CIP Register Object or the CIP Assembly object by using Host Parameter 36 - [Msg Flt Action].respectively let you determine the action of the option module and connected drive if communication is disrupted, the controller is idle, peer I/O is disrupted, or explicit messaging for drive control is disrupted. By default, these parameters fault the drive. You may configure these parameters so that the drive continues to run, however, precautions should be taken to verify that the settings of these parameters do not create a risk of injury or equipment damage. When commissioning the drive, verify that your system responds correctly to various situations (for example, a disconnected network cable, controller in idle state or explicit message control disruption).
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
