產品內容介紹
A-B 8520-4APA1輸入輸出模塊
連接選項驅動器模塊選項模塊與驅動器的連接方式因模式而異在其中操作選項模塊。
在適配器模式下操作時在端口的PowerFlex 750系列驅動器控制盒中安裝選項模塊4、5或6。有關更多安裝詳細信息，請參閱網絡通信選項卡安裝說明，出版物750COM-IN002，隨附選項模塊。
1.斷開驅動器電源。
2.卸下驅動器蓋，提起驅動器HIM擋板至打開狀態位置以訪問驅動控制箱。
3.使用防靜電措施。
4.將以太網電纜的一端連接到網絡。5.根據網絡拓?fù)洌瑘?zhí)行以下操作之一：
?星形網絡拓?fù)渎酚梢蕴W(wǎng)電纜的另一端從網絡穿過驅動器底部，然后插入電纜插入選項模塊的ENET1或ENET2網絡端口。
?線性或DLR網絡拓?fù)渎酚傻揭蕴W(wǎng)電纜從網絡穿過第一個驅動器的底部，并將其電纜插頭插入選項模塊ENET1網絡端口。要連接到第二個驅動器，請?jiān)诘谝粋€(gè)驅動器的選項模塊ENET2網絡端口和第二個驅動器的選項模塊ENET1網絡端口。
要連接其他驅動器，請?jiān)谥兄貜?fù)這些菊花鏈連接配置和驗證關鍵驅動器參數的方法相同PowerFlex 750系列驅動器可以單獨配置用于控制和各種組合的參考函數。
例如，您可以將使其控制的驅動器來自具有來自網絡的參考。或者您可以將驅動器設置為控制來自網絡，引用來自另一個外圍或接線板。或者您可以將驅動器設置為同時控制和參考來自網絡。
本節中的以下步驟假設驅動器將接收邏輯來自網絡的命令和引用。
1.驗證驅動器參數301-[Access Level]設置為“1”（高級）或“2”（專家）訪問此程序中所需的參數。
2.使用驅動器參數545-[Speed Ref A Sel]設置驅動器速度
參考文獻：
a、 將端口字段設置為“0”，如下所示。將參數字段設置為指向選項所在的端口（插槽）模塊已安裝（對于本例，端口4參考）。
示例對話框參數字段中的數字“874”上面是驅動器中指向端口的參數。
3.驗證驅動器參數930-[Speed Ref Source]是否報告驅動器引用的源（端口0）是選項所在的端口模塊已安裝（對于本例，端口4參考）。
這確保從網絡命令的任何參考可以使用驅動器參數002-[Commanded SpdRef]進行監控。
Connecting the Option Module to the Drive
The option module is connected to the drive differently depending on the mode in which the option module is operated. When Operating in Adapter Mode Install the option module in the PowerFlex 750-Series drive control pod in Port 4, 5 or 6. For more installation details, see the Network Communication Option Card Installation Instructions, publication 750COM-IN002, provided with the option module.1. Remove power from the drive. 2. Remove the drive cover and lift up the drive HIM bezel to its open position to access the drive control pod. 3. Use static control precautions. 4. Connect one end of the Ethernet cable to the network.5. Depending on the network topology, do one of the following: ? Star Network Topology—Route the other end of the Ethernet cable from the network through the bottom of the drive, and insert its cable plug into the option module’s ENET1 or ENET2 network port. ? Linear or DLR Network Topology—Route the other end of the Ethernet cable from the network through the bottom of the first drive, and insert its cable plug into the option module ENET1 network port. To connect to the second drive, attach another Ethernet cable between the first drive’s option module ENET2 network port and the second drive’s option module ENET1 network port. To connect additional drives, repeat these daisy-chain connections in the same way
Configuring and Verifying Key Drive Parameters
The PowerFlex 750-Series drive can be separately configured for the control and Reference functions in various combinations. For example, you could set the drive to have its control come from a peripheral or terminal block with the Reference coming from the network. Or you could set the drive to have its control come from the network with the Reference coming from another peripheral or terminal block. Or you could set the drive to have both its control and Reference come from the network. The following steps in this section assume that the drive will receive the Logic Command and Reference from the network. 1. Verify that drive Parameter 301 - [Access Level] is set to “1” (Advanced) or “2” (Expert) to access the required parameters in this procedure. 2. Use drive Parameter 545 - [Speed Ref A Sel] to set the drive speed Reference: a. Set the Port field to “0” as shown below
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
