產品內容介紹
1756-PA72/C交流電源模塊
設置輸入平均投資可以補償雜散噪聲和其他形式的振幅通過制作最新輸入樣本來通過模擬輸入濾波器的調制移動平均值的一部分&數字濾波的一種形式。這種移動平均技術對更新間隔沒有影響。
下表顯示了用于在七個輸入平均值中進行選擇的Sw–B設置8和4電路配置的采樣周期。
除平均采樣外，Sw–B還具有其他功能；開關B7設置為ON對于二進制代碼輸出或對于A組的十進制代碼輸出為OFF（輸入1-48電路模式和4電路模式中的輸入1-2）。開關B8的作用相同對于B組，由于模塊在出廠時經過校準，設計者的意圖是10 V參考電壓調整將有效一年。它應該是此后每年重新校準。
需要以下工具來調整模塊的參考電壓：精度為0.0001 V、電壓為10 V的精密數字讀數伏特計
刻度：6-1/2位，保證4位計數精度。
一把1/8英寸的薄刃螺絲刀。
一把小頭十字螺絲刀。用粘合劑（如Loctite或Glyptol）固定微調電位器調整螺釘注意：在重新校準過程中，現場接線可能會保持連接，因為模塊的工作狀態和參考電壓調整不相互影響。
模塊不需要預熱即可達到溫度。使用下表安裝模塊。
步驟操作
1從裝運箱中取出模塊并檢查是否損壞。如果發現損壞，請聯系分銷商（或銷售人員）正確的返回程序。
2確保從外殼上斷開電源。
3按如下方式配置開關組A：A-1至A-6適用于預期八或四電路配置的預期輸入電壓范圍A7選擇八路或四路輸入模式。A8至ON，用于正常操作。
4按如下方式配置交換機組B：B-1至B-6，適用于八或四電路配置的所需輸入平均樣本數上面指定的。B7選擇輸出代碼格式
5如果使用鍵銷（隨外殼裝運提供），則將其安裝在為此選擇的外殼槽的上方和下方模塊的安裝。
6打開手柄，將模塊插入外殼，將邊緣連接器牢牢固定在底板上。
7使用模塊前面板頂部和底部的固定安裝螺釘固定模塊。
8參考下面的現場連接器/輸入電路引腳分配圖。將現場側接線連接到雙現場連接器（位于（位于左側、前緣），根據需要鋪設成扇形的電纜。注：使用現場連接器接線尺寸AWG-20（含）（實心或絞合）。
9如果正在使用電流檢測輸入電路，將現場連接器上的相應電流檢測端子跨接至相應的熱輸入（+），如下面的現場連接器/輸入電路引腳分配圖所示。
注：應終止未使用的輸入，以減少因浮動輸入而產生的電氣噪聲和其他干擾線將未使用的電壓和電流端子（包括屏蔽）跨接至外殼接地。外殼接地僅為如果H8XX外殼接地，則有效。屏蔽的兩端不能連接到設備和模塊，除非設備屏蔽是設備輸入電路的一部分，并且未在內部連接到設備外殼接地。
注意：
如果需要超范圍和欠范圍檢測，并且此檢測會導致吞吐量問題未使用的通道（因為它們浮動或峰值超出范圍），然后未使用的電壓或電流通道現場連接器應與有效輸入通道并聯。只要有效通道保持在范圍內，綁定頻道也將保持在范圍內。
注：對于4-20 mA范圍內的電流，只有有效輸入需要包含250? 電阻器。
10參考下面的現場連接器安裝圖。用針腳1將兩個有線現場連接器安裝在模擬模塊上位于頂部，現場接線位于左側。
11關閉模塊手柄。
12如果需要，打開殼體電源。
注：如果在電壓模式下操作時出現斷路，輸入可能需要幾秒鐘才能衰減至零，由于前端RC網絡。如果需要開路檢測，模塊應在當前模式。添加250? 電阻器迫使RC網絡快速放電
Setting Input Averaging
It is possible to compensate for spurious noise and other forms of amplitude modulation coming through the analog input filter by making the latest input sample part of a moving average–a form of digital filtering. This moving average technique has no affect upon the update interval. The following tables show Sw–B setting for selecting among seven input average sample periods for both 8 and 4 circuit configurations. Sw–B has other functions in addition to average sampling; Switch B7 is set to ON for binary code output or OFF for decimal code output for Group A (inputs 1-4 in the 8 circuit mode and inputs 1-2 in the 4 circuit mode). Switch B8 does the same for Group B.Since the module is shipped factory-calibrated, it is the designer’s intention that the 10 V reference voltage adjustment will be good for one year. It should be recalibrated annually thereafter. The following tools are needed to adjust the module’s reference voltage: A precision digital readout voltmeter with an accuracy of 0.0001 V on a 10 V scale: 6-1/2 digits, to guarantee 4 bit count accuracy. A 1/8-inch bit, thin-blade screwdriver. A small-bit Phillips-head screwdriver. An adhesive (such as Loctite or Glyptol) to secure trim-pot adjustment screws Note: Field wiring may remain connected during the recalibration procedure, as the module’s working state is not interactive with the reference voltage adjustment. Also, the module does not require warmup to attain temperature.
Use the following table to install the module.
Step Action 1 Remove module from shipping box and check for damage. If damage found, contact distributor (or sales person) for correct return procedure. 2 Ensure that power is removed from housing. 3 Configure switch bank A as follows: A-1 through A-6 for desired input voltage ranges appropriate to the intended eight- or four-circuit configuration A7 to select eight- or four-circuit input mode. A8 to ON for normal operation. 4 Configure switch bank B as follows: B-1 through B-6 for desired number of input averaging samples appropriate to eight- or four-circuit configuration designated above. B7 to select output code format 5 If using key pins (provided with housing shipment), install them above and below housing slot selected for this module’s installation. 6 Open handle and insert module into housing, firmly seating edge connector in backplane. 7 Secure module using captive mounting screws at top and bottom of module’s front panel. 8 Refer to field connector/input circuit pinout diagram, below. Connect field side wiring to double field connector (located on left side, front edge), laying in cable fan-out as desired.
NOTE:
Use field connector wiring sizes AWG—20 inclusive (solid or stranded). 9 If current sense input circuit(s) is being used, jumper appropriate current sense terminal on field connector to corresponding hot input (+) as shown in field connector/input circuit pinout diagram, below. NOTE: Unused inputs should be terminated to reduce electrical noise and other interference due to floating input lines. Jumper unused voltage and current terminals (including shields) to case ground. Case ground will only be effective if H8XX housing is connected to earth ground. Both ends of the shield cannot be connected to the device and module, unless the device shield is part of the device input circuit, and is not connected internally to the device case ground. NOTE: If over-range and under-range detection is required, and this detection is causing throughput problems with the unused channels (because they float or spike outside the range) then the unused voltage or current channels at the field connector should be connected in parallel to a valid input channel. As long as the valid channel stays within range, the tied channels will also stay within range. NOTE: For currents within the range of 4—20 mA, only the valid input requires the inclusion of the 250 ? resistor. 10 Refer to field connector mounting drawing, below. Mount two wired field connectors on analog module with pin 1 positioned at top and field wiring to left. 11 Close module handle. 12 Turn on power to housing if desired. NOTE: If an open circuit occurs when operating in the voltage mode, the input may take several seconds to decay to zero, due to the front-end RC network. If open-circuit detection is required, the module should be operated in the current mode. The addition of the 250 ? resistor forces the RC network to discharge rapidly
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
