產品詳情內容介紹
DYNOMAX 10-2A-B-1165驅動控制減速機
信道抑制按下工程卡INHIBIT（禁止）按鈕可切換選定的控制卡通道抑制模式介于打開和關閉之間。
當抑制模式設置為打開時，從工程部本地卡或遠程抑制輸入，所選控制卡：
a、 通道抑制繼電器（如已配置）啟動。
b、 通道LED顯示持續琥珀色以指示INHIBIT（抑制）。
c、 其余通道繼電器鎖定在非活動狀態。
要選擇禁止功能，請執行以下操作：
（1） 將工程鑰匙插入工程卡前面板插座，并檢查解鎖指示燈（）是否亮起。
（2） 按住所需的控制卡重置/選擇按鈕約1.5秒，檢查所選的控制卡通過顯示選擇來指示它已被選中
（3） 使用工程卡（）和（）按鈕選擇所需通道。
（4） 按下INHIBIT（抑制）按鈕以打開通道抑制模式/關閉。報警配置和繼電器測試操作通過不同的
階段如下：
a、 設置A1、A2、A3、STEL、LTEL的閾值。這些階段用于設置A1、A2、A3、STEL和LTEL警報閾值點，不影響報警LED和繼電器。
b、 A1、A2、A3、故障、STEL、LTEL的測試燈和可選繼電器。
這些階段提供燈測試和繼電器測試功能。
注：未配置STEL/LTEL閾值時，一行破折號將顯示而不是標高和STEL和LTEL設施將永久設置為關閉。
要選擇報警配置操作，請執行以下操作：
（1） 將工程鑰匙插入工程卡前面板插座，并檢查解鎖指示燈（）是否亮起。
（2） 按住所需的控制卡重置/選擇按鈕約1.5秒，檢查所選的控制卡通過顯示選擇來指示它已被選中偶像
（3） 使用工程卡（）和（）按鈕選擇所需通道。
（4） 第一次按下工程卡報警按鈕。
（5） 檢查所選控制卡信息顯示屏是否顯示A1上升報警閾值或A1代表下降報警閾值交替使用選定的頻道編號。
（6） 檢查所選控制卡數字顯示器是否指示A1報警閾值。
模擬顯示屏繼續實時顯示傳感器測量
1.只有在控制卡已為此警報配置。
2.測試功能自動禁用控制卡允許對通道進行顯示測試和指示燈測試的通道
LED報警指示，防止意外報警生成。為了測試?yán)^電器和故障指示，必須使用INHIBIT（禁止）按鈕來設置控制卡進入不受限制的狀態。
3.在測試中，可以取消選擇所選控制卡按下所選控制卡前面板RESET/選擇按鈕。模擬氣體液位和繼電器狀態將保持設置，允許多個控制卡同時測試。重新選擇控制卡時卡將返回測試模式。ATTN LED指示燈哪些卡在報警測試模式下具有通道。
4.如果禁用被解除，外部繼電器將運行。
ALARM CONFIGURATION AND RELAY TEST
The alarm configuration and relay test operation cycles through different stages as follows: a. Set thresholds for A1, A2, A3, STEL, LTEL. These stages are used to set the A1, A2, A3, STEL and LTEL alarm threshold points and do not affect the alarm LEDs and relays. b. Test lamps and optional relays for A1, A2, A3, Fault, STEL, LTEL. These stages provide a lamp test and relay test function. Note: When not configured for STEL/LTEL threshold, a row of dashes will be displayed instead of a level and the STEL and LTEL faclilities will be set permanently to off. To select the alarm configuration operation, proceed as follows: (1) Plug the Engineering Key into the Engineering Card front panel socket and check that the Unlocked LED ( ) is illuminated. (2) Push and hold the required control card RESET/SELECT pushbutton for approximately 1.5 seconds and check that the selected control card indicates it has been selected by displaying the select icon. (3) Use the Engineering Card ( ) and ( ) push-buttons to select the required channel. (4) Push the Engineering Card ALARMS push-button for the first time. (5) Check that the selected control card message display shows A1 for a rising alarm threshold or A1 for a falling alarm threshold alternating with the selected channel number. (6) Check that the selected control card digital display indicates the A1 alarm threshold point. Note: The analogue display continues to show the sensor live measurement.
CHANNEL INHIBIT
Pushing the Engineering Card INHIBIT push-button toggles the selected control card channel inhibit mode between on and off. When the inhibit mode is set to on, either locally from the Engineering Card or remotely by the Remote Inhibit input, the selected control card: a. channel inhibit relay, if configured, is actuated. b. channel LED shows continuous amber to indicate INHIBIT. c. remaining channel relays are locked in their non-active state. To select the inhibit function, proceed as follows: (1) Plug the Engineering Key into the Engineering Card front panel socket and check that the Unlocked LED ( ) is illuminated. (2) Push and hold the required control card RESET/SELECT pushbutton for approximately 1.5 seconds and check that the selected control card indicates it has been selected by displaying the select icon. (3) Use the Engineering Card ( ) and ( ) push-buttons to select the required channel. (4) Push the INHIBIT push-button to toggle the channels inhibit mode on/ off.
: 1. The LTEL Alarm can only be switched on if the Control Card has been configured for this alarm. 2. The TEST function automatically inhibits the control card channel to allow a display test and a lamp test of the channel LED alarm indications and prevent accidental alarms being generated. In order to test the relays and FAULT indications, the INHIBIT push-button must be used to set the control card channel into the uninhibited state. 3. A selected control card may be deselected while in the TEST mode by pushing the selected control card front panel RESET/ SELECT push-button. The simulated gas level and relay states will remain set allowing several control cards to be tested simultaneously. When the control card is reselected the card will return to the TEST mode. The ATTN LED indicates which cards have channels in the alarm test mode. 4. If the inhibit is removed, the external relays will operate.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營產品文字介紹
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
