產品詳情內容介紹
B&R 5AP1130.156C-000控制觸摸屏
工程操作程序根據操作的鍵盤功能按鈕
可執行以下工程操作程序：
通道重置。
頻道選擇。
通道抑制。
報警配置和繼電器測試。
催化橋電流調整。
零信號校準。
量程信號校準。
第一量程信號校準。
傳感器信號監測。時鐘/日歷調整。
通道選擇和復位由通道卡reset執行/選擇按鈕。見第6章第3節。
其余工程功能在控制卡之后執行已使用工程卡按鈕控件選擇。工程師的操作說明是指附加設施可用于設置和維護系統。
因為系統可以被這些功能改變或阻礙，它們只能工程部解鎖工程卡時執行鑰匙選擇操作后，有四個控制按鈕可用于根據需要操縱操作。這些是：a、 向上按鈕，可用于提升選定的控制卡指示值。如果保持在操作位置顯示將每0.5秒增加一個單位。
b、 向下按鈕，可用于降低選定的控制卡指示值。如果保持在操作位置顯示將每0.5秒減少一個單位。
c、 接受按鈕，可用于接受所選控制卡顯示的值并永久存儲作為配置的一部分。將控制卡返回所選模式。
信道抑制按下工程卡INHIBIT（禁止）按鈕可切換選定的控制卡通道抑制模式介于打開和關閉之間。
當抑制模式設置為打開時，從工程部本地卡或遠程抑制輸入
所選控制卡：
a、 通道抑制繼電器（如已配置）啟動。
b、 通道LED顯示持續琥珀色以指示INHIBIT（抑制）。
c、 其余通道繼電器鎖定在非活動狀態。
要選擇禁止功能，請執行以下操作：
（1） 將工程鑰匙插入工程卡前面板插座，并檢查解鎖指示燈是否亮起。
（2） 按住所需的控制卡重置/選擇按鈕約1.5秒，檢查所選的控制卡通過顯示選擇來指示它已被選中偶像
（3） 使用工程卡（）和（）按鈕選擇所需通道。
（4） 按下INHIBIT（抑制）按鈕以打開通道抑制模式/關閉。
拒絕按鈕，可用于拒絕選定的控制卡顯示值并返回到先前的設定值。將控制卡返回到所選模式。
ENGINEERING OPERATING ROUTINES
Depending upon the which keypad function push-button is operated, the following engineering operating routines may be carried out: Channel Reset. Channel Select. Channel Inhibit. Alarm Configuration and Relay Test. Catalytic Bridge Current Adjustment. Zero Signal Calibration. Span Signal Calibration. 1st Span Signal Calibration. Sensor Signal Monitoring. Clock/Calendar Adjustment. Channel select and reset are carried out by the channel card RESET/ SELECT push-button. See Chapter 6, Section 3. The remaining engineering functions are carried out after a control card has been selected using the Engineering Card push-button controls.The engineer's operating instructions refer to the additional facilities available to setup and maintain the system. Because the operation of the system can be altered or impeded by these functions, they can only be performed when the Engineering Card is unlocked by the Engineering Key.Once an operation has been selected, there are four control push-buttons which may be used to manipulate the operation as required. These are: a. The up push-button, which may be used to raise the selected control card indicted value. If held in the operated position, the display will be increased by one unit every 0.5 seconds. b. The down push-button, which may be used to lower the selected control card indicated value. If held in the operated position, the display will be decreased by one unit every 0.5 seconds. c. The accept push-button, which may be used to accept the selected control card displayed value and store this permanently as part of the configuration. Returns the control card to the selected mode.
CHANNEL INHIBIT
Pushing the Engineering Card INHIBIT push-button toggles the selected control card channel inhibit mode between on and off. When the inhibit mode is set to on, either locally from the Engineering Card or remotely by the Remote Inhibit input, the selected control card: a. channel inhibit relay, if configured, is actuated. b. channel LED shows continuous amber to indicate INHIBIT. c. remaining channel relays are locked in their non-active state. To select the inhibit function, proceed as follows: (1) Plug the Engineering Key into the Engineering Card front panel socket and check that the Unlocked LED ( ) is illuminated. (2) Push and hold the required control card RESET/SELECT pushbutton for approximately 1.5 seconds and check that the selected control card indicates it has been selected by displaying the select icon. (3) Use the Engineering Card ( ) and ( ) push-buttons to select the required channel. (4) Push the INHIBIT push-button to toggle the channels inhibit mode on/ off.
The reject push-button, which may be used to reject the selected control card displayed value and return to the previous set value. Returns the control card to the selected mode.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營產品文字介紹
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
