產品詳情內容介紹
Kollmorgen 6SM56-S3000-G伺服自動化電機
這與上顯示的錯誤代碼消息ERxx有關LCD消息顯示。如果出現多個錯誤
同時出現，代碼最高的錯誤顯示數字
卡片狀態：指控制卡片操作的狀態。
激活表示卡仍在處理信號從連接的傳感器，如果是傳感器
檢測氣體時，仍會激活任何配置的警報輸出。
非活動意味著無法進行控制生成任何報警以響應傳感器的卡檢測氣體。
故障信號：這是指對錯誤條件的響應。
是表示相應通道前面板故障LED和任何配置的故障繼電器將運行。
否表示未給出故障指示。錯誤導致這些一般警告消息的條件屬于次要性質，頻道卡將繼續運轉然而，情況應該仍然是調查。
閂鎖：這是指錯誤消息和相關故障信號。
是表示控制卡將繼續顯示錯誤消息，直到導致錯誤的條件已清除，并且已操作復位按鈕。否表示錯誤消息將自動清除一旦導致錯誤消息的條件變明朗。
Conf表示閂鎖/非閂鎖狀態為可使用工程接口軟件進行配置。硬件故障如果出現以下情況，則顯示硬件故障消息通道卡檢測到其故障
操作或傳感器輸入故障。檢查傳感器連接。移除通道卡并將其插入兼容的工作通道并檢查其操作
（此操作過程中可能會出現ER86-這是正常的）。如果卡片上仍顯示故障，必須更換。如果卡是工作時，應更換傳感器。顯示低于范圍故障消息當傳感器信號讀數小于通道內保持的預定電平配置數據。
通常這是由于傳感器或傳感器電纜安裝打開電路將顯示超范圍故障信息
當傳感器信號讀數高于通道內保持的預定水平配置數據。通常，這是由于傳感器或傳感器電纜安裝短環行或者，傳感器可以檢測到非常高的氣體含量。
鎖定信號超范圍故障的復位條件只能在以下情況下執行檢查傳感器是否清潔（非目標氣體）空氣。這允許將卡移動到其他位置用于故障查找的插槽位置。這安裝時也可能顯示消息
新通道卡或安裝備用卡替換可以清除消息將通道卡校準為新的插槽位置和連接的傳感器。
根據報警配置，將通道卡移動到備用插槽可能會影響警報的生成。
報警操作應在卡已經移動和校準。
COMMISSIONING AND MAINTENANCE INSTRUCTIONS
Hardware Fault The hardware fault message is displayed if the channel card detects a fault in its operation or a fault with a sensor input. Check the sensor connections. Remove the channel card and insert it into a compatible working channel and check its operation (ER86 may appear during this operation - this is normal). If the card still indicates a fault, it must be replaced. If the card is working, the sensor should be replaced.The under range fault message is displayed when the sensor signal reading is less than the predetermined level held within the channel configuration data. Typically this is due to either the sensor or the sensor cable installation being open circuit
The over range fault message will appear when the sensor signal reading is above the predetermined level held within the channel configuration data. Typically, this is due to either the sensor or the sensor cable installation being short circuit. Alternatively, the sensor may be detecting a very high level of gas. The reset of a latched signal overrange fault condition should only be carried out after checking that the sensor is in clean (non target gas) air.
This allows cards to be moved to alternative slot locations for fault finding purposes. This message may also be displayed when fitting a new channel card or fitting a spare replacement. The message can be cleared by calibrating the channel card to the new slot location and connected sensor. Depending on the alarm configuration, moving channel cards to alternative slots may compromise the generation of alarms. The alarm operation should be checked after the card has been moved and calibrated.
ERROR CODES
This relates to the error code message ERxx displayed on the LCD message display. If more than one error is present simultaneously, the error with the highest code number is displayed Card Status: This refers to the condition of the control card operation. Active means that the card is still processing signals from the connected sensor and, in the event of the sensor detecting gas, will still activate any configured alarm outputs. Non active means that it is not possible for the control card to generate any alarms in response to the sensor detecting gas. Fault Signal: This refers to the indication of the fault condition in response to the error condition. Yes means that the appropriate channel front panel fault LED and any configured fault relay will be operated. No means that no fault indication is given. The error condition that causes these general warning messages is of a minor nature and the channel card will continue to operate. The condition should however still be investigated. Latch: This refers to the condition of the error message and the associated fault signal. Yes means that the control card will continue to display the error message until the condition causing the error has cleared and the reset push-button has been operated. No means that the error message will clear automatically once the condition causing the error message has cleared. Conf. means that the latch/non-latch condition is configurable using the Engineering Interface Software.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營產品文字介紹
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
