公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
產品詳情介紹
KOKUSAI BALEXT-SMP數控電路板
執行和讀取I/O配置系統結構有以下可能性當使用07 KR 91、07 KT 92或07 KT 93作為公交車時
主控形狀：通過總線主中央單元07 KR 91的用戶程序，07 KT 92或07 KT 93，通過執行和讀取I/O配置航站樓設施或從遠程讀取I/O配置模塊。
通過執行和讀取I/O配置用戶程序
功能塊CS31CO可用于I/O模塊的配置。此功能塊是
描述了編程軟件907 PC 331在相應的文檔中。
通過執行和讀取I/O配置碼頭或TCZ的方式
此方法基于以下事實：07 KR 91、07 KT 92和07 KT 93使用對話編程接口上的語言，它允許I/O配置由執行和查詢簡單協議的方式；見第7.3卷第3章，“MAIL命令”。07 KR 91和07 KT 92/93通常配備I/O配置的特殊功能。
以下設備可用作終端：
商用終端，配備EIA–232接口，如VT100。
配備編程軟件907的PCPC 331。所有接口數據都正確設置在“PLC通信2”主菜單項，子項“終端仿真”。
運行模式下的維修設備TCZ
1=端子，2=圖表。模式，N=變速箱速度不變，9600波特。
讀取I/O配置和診斷數據
遠程模塊
讀取的I/O配置和診斷數據遠程模塊的I/O終端將顯示在以下是設備ICSC 08 L1的示例。這個測試按鈕4，LED顯示模塊的1必須用于此的。
第一次按下測試按鈕時，通道選擇E/A0（輸入/輸出0）：LED 0閃爍。之后釋放按鈕，此通道的診斷數據由黃色LED 0至7顯示約3秒。
LED具有以下含義：
0 UE=單元錯誤
1 BE=總線錯誤
2未使用
3 CI/CO=輸入/輸出斷線
4 OL=過載
5 SC=短路
6輸出配置
7作為輸入的配置如果LED 6和7同時亮起，則通道配置為組合輸入/輸出。
LED 2的含義也印在前面模塊的面板。
對其他每個通道重復此操作按下并釋放測試按鈕的時間。
Performing and reading the I/O
configuration
There are the following possibilities for system structures
when using 07 KR 91, 07 KT 92 or 07 KT 93 as bus
master:
Performing and reading the I/O configuration via the
user program of the bus master central unit 07 KR 91,
07 KT 92 or 07 KT 93,
Performing and reading the I/O configuration by
means of the terminal or
Reading the I/O configuration from the remote
modules.
Performing and reading the I/O configuration via
the user program
The function block CS31CO is available for the I/O
configuration of the modules. This function block is part of
the programming software 907 PC 331 and is described
in the corresponding documentation.
Performing and reading the I/O configuration by
means of the terminal or TCZ
This method is based on the fact that the central units
07 KR 91, 07 KT 92 and 07 KT 93 use a dialogue
language at the programming interface which allows the
I/O configuration to be performed and interrogated by
means of simple protocols; see volume 7.3, chapter 3,
”MAIL command”.
07 KR 91 and 07 KT 92/93 are generally equipped with
the special function for I/O configuration.
The following devices can be used as terminal:
A commercially available terminal equipped with an
EIA–232 interface, such as VT100.
A PC equipped with the programming software 907
PC 331. All the interface data are correctly set under
the main menu item of ”PLC communication 2”,
sub-item ”Terminal emulation”.
The service device TCZ in the operating mode
1 = TERMINAL, 2 = CHAR.MODE, N = transmission
speed unchanged, 9600 Baud.
Reading I/O configuration and diagnosis data at the
remote module
Reading the I/O configuration and the diagnosis data for
an I/O terminal of a remote module will be shown in the
following for the device ICSC 08 L1 as an example. The
test button 4 and the LED displays 1 of the module
have to be used for this purpose.
When the test button is pressed for the first time, channel
E/A0 (input/output 0) is selected: LED 0 flashes. After
releasing the button, the diagnosis data of this channel
are shown by the yellow LEDs 0 to 7 for approx. 3
seconds.
The LEDs have the following meaning:
0 UE = Unit error
1 BE = Bus error
2 not used
3 CI/CO = Cut wire of inputs/outputs
4 OL = Overload
5 SC = Short circuit
6 Configuration as output
7 Configuration as input
If the LEDs 6 and 7 light up at the same time, the
channel is configured as a combined input/output.
The meaning of the LEDs 2 is also printed onto the front
panel of the module.
The operation is repeated for the other channels each
time the test button is pressed and released.
