ALSTOM 3BEE0226電源配套接口板
CPU板包含微處理器和RAM存儲器、實時時鐘、LED指示燈、Init按鈕和CompactFlash界面
PM851A控制器的底板有兩個RJ45以太網端口（CN1、CN2）用于連接控制網絡，以及兩個RJ45串行端口（COM3、COM4）。
請注意，PM851/PM851A僅限于一個以太網（CN1）端口，因此冗余以太網不可用。連載之一
端口（COM3）是帶有調制解調器控制信號的RS-232C端口，而另一個端口（COM4）被隔離并用于配置工具的連接。
簡單的DIN導軌連接/拆卸程序，使用獨特的滑動和鎖定機制。所有底板均配有唯一的以太網地址，為每個CPU提供硬件身份地址可以在以太網地址標簽上找到連接到TP830基板。一般評論術語“DCS晶閘管功率轉換器”是ABB基本直流轉換器的通用名稱。本學期可以在相關文檔的許多部分找到。根據下面給出的簡要描述描述了特定單元的特征。
DCS 500和DCS 500B的簡要說明
DSC 500B單元范圍是從DCS 500范圍發展而來的增強。之間的差異控制板版本中有兩個范圍：用于DCS 500B裝置范圍的控制板為SDCS-CON-2型，與SDCS-CON-1型有幾點不同（見下表）。
DCP 500和DCP 500B的簡要說明在DCP 500單元中，這改變了其視覺外觀、安裝尺寸和電源部分之間的接口以及電子設備。DCP裝置在功能上與DCS裝置兼容，因為電子設備（電源組件、控制板和選項和/或控制）是相同的。DCP 500B單元范圍是一個增強
從DCP 500系列開發而來，兩個系列之間的差異在于控制板：用于DCP 500B裝置范圍的控制板為SDCS-CON-2型，與SDCSCON-1型有幾點不同（見下表）。DCF 500B簡介
軟件版本為21.232或更高版本時，DCS 500B具有“三相勵磁機模式”。DCF 500B是基于可編程DCS 500B軟件和SDCS-CON-2控制板的三相勵磁機。
修改了接口板引腳1x/引腳2x；-需要過電壓保護單元DCF 505/506。
DCS 600簡介
DCS 600變頻器系列基于為DCS 500B型開發的硬件。
使用SDCS_AMC_DC板代替COM-x板。PC工具將連接到那里，以及如果APC用作PLC，則為APC（應用程序控制器）。如果使用不同的PLC，則使用單獨的適配器需要模塊。它們也必須連接到AMC-DC板。軟件代碼總是開始S15.xxx適用于多驅動，S18.xxx用于起重機驅動。
The CPU board contains the microprocessor and RAM memory, a realtime clock, LED indicators, INITpush button, and a CompactFlash
interface.
The base plate of the PM851A controller has two RJ45 Ethernet ports
(CN1, CN2) for connection to the Control Network, and two RJ45
serial ports (COM3, COM4).
Note that a PM851/PM851A is restricted to one Ethernet(CN1)
port, thus redundant Ethernetis not available. One of the serial
ports (COM3) is an RS-232C portwith modemcontrol signals,
whereas the other port(COM4) is isolated and used for the
connection of a configuration tool.
Simple DIN rail attachment / detachment procedures, using the
unique slide & lock mechanism. All base plates are providedwith a
unique Ethernet address which provides every CPUwith a hardware
identity. The address can be found on the Ethernet address label
attached to the TP830 base plate.General remarks
The term “DCS thyristor power converter” is a general designation for basic DC converters from ABB. This term
can be found in many parts of the relevant documentation. The precise product name in accordance with the
brief descriptions given below characterizes a specific unit.
Brief description of DCS 500 and DCS 500B
The DSC 500B unit range is an enhancement developed from the DCS 500 range. The difference between the
two ranges lies in the version of the control board: the control board used for the DCS 500B unit range is the
SDCS-CON-2 type, which is different from the SDCS-CON-1 type in several points (see the table below).
Brief description of DCP 500 and DCP 500B
In the DCP 500 unit, the electronics of the DCS 500 unit have been equipped with a different power section,
which changes its visual appearance, its installation dimensions and the interface between the power section
and the electronics. The DCP unit is functionally compatible with the DCS unit, since the electronics (power
pack, control board and options and/or control) are identical. The DCP 500B unit range is an enhancement
developed from the DCP 500 range, with the difference between the two ranges lying in the control board: the
control board used for the DCP 500B unit range is the SDCS-CON-2 type, which is different from the SDCSCON-1 type in several points (see the table below).Brief description of DCF 500B
With software release 21.232 or higher DCS 500B has a '3-phase field exciter mode'. A DCF 500B is a threephase field exciter based on the programmable DCS 500B software and the SDCS-CON-2 control board.
The interface boards PIN-1x/PIN-2x are modified; - an overvoltage protection unit DCF 505/506 is required.
Brief description of DCS 600
The DCS 600 converter family is based on the hardware developed for the DCS 500B type.
Instead of a COM-x board, the SDCS_AMC_DC board is used. PC tools will be connected there, as well as
the APC (Application controller), if the APC is used as a PLC. If a different PLC is used, separate adapter
modules are needed. They must be connected to the AMC-DC board, too. The software code always begins
with S15.xxx for MultiDrive or S18.xxx for Crane drives.
