SYHNC100-NIB-23/W-24-P-D-E23-A012,驅動器
報警信號將顯示在的七段顯示屏上
控制板SDCS-CON-3，代碼A
控制面板DCS 400以明文形式平移。警報信號將僅如果沒有激活的故障信號，則顯示。
除A9（緊急停止）外，報警信號：
不會導致驅動器停止。參數恢復
要在中啟用數據丟失，請執行以下操作：
要檢測的FlashProm參數扇區由校驗和。可能會發生數據丟失
如果存在技術缺陷：如果在參數更改和5秒保存周期。為了安全原因是，在參數區域上方提供了第二個備份扇區，其中故障記錄器保持更新副本。
如果在中檢測到數據丟失參數扇區，此備份扇區將被激活，并且參數恢復。恢復操作觸發A18-參數停止報警。這個然而，驅動器將保持功能，并且可以使用重置按鈕確認報警。
必須檢查最近輸入的參數，必要時再次輸入
只有在備份扇區中發現數據丟失時為安全起見，應禁用驅動器
原因和F2硬件故障觸發，也可能與F4相伴-ParamChecksum錯誤。這些無法確認故障。
當您再次關閉和打開電子設備電源時，所有參數將重置為初始值（出廠設置）。
如果此FlashProm效果仍然存在，則下一次校驗和檢查
例程將再次觸發故障停機
如果事實證明只是暫時的效果，驅動器必須在下一次啟動前重新參數化，e、 g.通過復制（之前備份）參數從將控制面板插入驅動器。
即使該故障似乎有已在電子設備電源切換后消除打開，曾經是FlashProm硬件
已檢測到問題，您必須預料到它可能會發生反復
Parameter Restored To enable data loss in the FlashProm to be detected, the parameter sector is secured by a checksum. Data loss may occur if there is a technical defect in the FlashProm or if the electronics supply is switched off between parameter change and the 5-second save cycle. For safety reasons, a second back-up sector is provided above the parameter area, where the parameters and the contents of the fault logger are kept as updated copies. If a data loss is detected in the parameter sector, this back-up sector will be activated, and the parameters restored. The restoration operation triggers the A18- ParameterRestored alarm. The drive will remain functional, however, and the alarm can be acknowledged using the reset button. The parameters most recently entered must be checked, and entered again if necessary. Only when a data loss is discovered in the back-up sector will the drive be disabled, for safety reasons, and the F2-Hardware fault triggered, which may also be accompanied by the F4- ParamChecksum fault. These faults cannot be acknowledged. When you switch the electronics supply off and on again, all parameters will be reset to their initial values (factory settings). If this FlashProm effect still persists, the next checksum check routine will again trigger a shutdown on fault. If it proves to have been a temporary effect, the drive must be reparameterised before the next start-up, e.g. by copying the (previously backed-up) parameters set from the control panel into the drive. Even if this fault appears to have been eliminated after the electronics supply has been switched on, once a FlashProm hardware problem has been detected, you have to expect that it may occur repeatedly.
