Rexroth VTS0234-47/AP025驅動卡件
在可以從面板控制驅動器之前,首先控制面板必須獲得控制權。小組的能力:控制:驅動由面板鎖定功能決定,該功能:可通過菜單選擇和LOC/REM訪問面板上提供的鑰匙。面板鎖定模式必須設置為解鎖或無par寫入,因為所有其他條目將阻止面板控制驅動器。使用LOC/REM鍵
以實際將控制轉移到面板。然后通過以下方式發出信號:狀態行中的LOC狀態指示。按鍵
這將再次導致面板放棄對驅動,狀態行中的LOC指示將消失。
實際值顯示
在面板顯示的第一行中,選擇的實際值
使用參數,面板動作1(6.16)至面板動作3(6.18)為:表明。所需的實際值必須用這些參數預先定義。控制驅動器時在面板中,實際值不斷更新。
參考顯示
在該行中,通過向上/向下設置速度參考顯示鍵。
狀態顯示
狀態行中的LOC表示驅動器正在被控制來自面板。
RUN in der狀態行表示驅動器已打開,并且啟用。
激活引用
參考值的任何修改必須由以下人員發起:
按下回車鍵,將生成參考值
以下劃線顯示。所需的參考值如下:使用向上/向下鍵設置。更改參考僅當參考值顯示為下劃線。使用向上/向下鍵,您可以設置任何速度
0 rpm和最大轉速之間的參考值,定義如下:參數最大速度(1.06)。
駕駛和啟動,駕駛和停止
警告:必須采取適當的安全預防措施在啟動驅動器之前。
此鍵的功能取決于當前驅動器狀態。
如果驅動器處于關閉狀態,按下此鍵將打開線路接觸器并啟用控制器。驅動器將根據預設斜坡時間(5.09)加速至選擇的速度參考。
如果驅動器處于打開狀態,按下此鍵將停止驅動器。
然后,驅動器將根據預設停止減速
模式(2.03)和斜坡時間(5.10,如果激活),并將切換離線接觸器。
改變參考極性
參考中指示的速度參考極性
按此鍵可更改顯示。電機將首先減速然后加速-僅在第四季度應用中-在相反的方向。
重置(故障確認)
轉換器檢測到的所有故障可通過以下方式進行重置:如果相關故障不存在,則按下此鍵不再活躍。
Before the drive can be controlled from the panel, the panel first
must be given permission to take control. The panel’s ability to
control the drive is determined by the Panel Lock function which
can be accessed through menu selection and by the LOC/REM
key provided on the panel. The Panel Lock mode must be set to
unlocked or no par write, since all other entries will prevent the
panel from taking control of the drive. The LOC/REM key is used
to actually transfer control to the panel. This is then signaled by
the LOC status indication in the status line. Pressing the key
once again will cause the panel to give up its command of the
drive, and the LOC indication in the status line will disappear.
Actual value display
In the first line of the panel display, the actual values selected
with the parameters Panel Act 1 (6.16) to Panel Act 3 (6.18) are
indicated. The desired actual values have to be defined beforehand with these parameters. When the drive is being controlled
from the panel, the actual values are continually updated.
Reference display
In this line, the speed reference set by means of the UP/DOWN
keys is displayed.
Status display
LOC in the status line indicates that the drive is being controlled
from the panel.
RUN in der status line indicates that the drive is switched on and
enabled.
Activate reference
Any modification of a reference value has to be initiated by
pressing the ENTER key, which will result in the reference value
displayed being underlined. The desired reference value is then
set using the UP/DOWN keys.Change reference
A reference value can be changed only when it is displayed with
an underline. Using the UP/DOWN keys, you can set any speed
reference between 0 rpm and the maximum speed defined with
the parameter Max Speed (1.06).
Drive ON and START, Drive OFF and STOP
CAUTION: Appropriate safety precautions must be taken
before starting the drive.
The function of this key is dependent on the current drive status.
If the drive is in the OFF state, pressing this key will switch ON
the line contactor and enable the controller. The drive will the
accelerate in accordance with the preset ramp time (5.09) up to
the selected speed reference.
If the drive is in the ON state, pressing this key will stop the drive.
The drive will then decelerate in accordance with the preset stop
mode (2.03) and ramp time (5.10, if activated) and will switch
OFF the line contactor.
Change reference polarity
The polarity of the speed reference indicated in the reference
display can be changed by pressing this key. The motor will first
decelerate and then accelerate - only in 4Q applications - in the
reverse direction.
Reset (Fault acknowledgement)
All faults detected by the converter can be reset by simply
pressing this key, provided that the faults concerned are no
longer active.