主營產品
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
HONEYWELL 51403645-100采集信號卡件
熱插拔到ExpressCard插槽。此設置僅適用于以下情況：ExpressCard熱插拔資源設置為已啟用。默認
此設置的值為4096字節的I/O空間。
?內存此設置決定內存空間的大小，以由BIOS為PCI-PCI網橋保留的字節熱插拔到ExpressCard插槽中。此設置僅適用如果ExpressCard熱插拔資源設置為已啟用。默認此設置的值為32 MB內存。
?預取內存：此設置決定將由可熱插拔到ExpressCard中的PCI-PCI橋的BIOS狹槽此設置僅適用于ExpressCard熱插拔資源設置為已啟用。此設置的默認值為：32兆字節的可預取內存。PXI設置菜單使用此菜單控制和路由PXI背板上的某些信號。
通常，您不需要修改這些設置。然而，其他本手冊的章節可能表明需要進行修改并且可能導致不可預測的行為。?APIC路由：此項僅適用于Windows XP和2000以及其他現代操作系統。選擇啟用以初始化單處理器模式下的IOAPIC和本地APIC。選擇“禁用”以使用中斷路由的傳統PIC。默認設置已啟用。
?PIRQx路由：此設置選擇PXI/PCI的路由選項
連接到PIRQx的設備。此設置會影響不使用的操作系統
APIC路由。所有PIRQx選項的默認設置為IRQ10。
?每個插槽設備設置：此設置將打開每個插槽設備設置子菜單。請參閱每個插槽設備設置子菜單部分
每個插槽設備設置子菜單
使用此菜單配置可針對單個PCI修改的選項PXI機箱中的設備。
注意：不能禁用在PCI橋后面的設備上掃描選項ROM。
PCI設備x選項ROM掃描此設置選擇是否使用PCI
將掃描設備x的選項ROM。將此選項設置為已啟用
允許BIOS掃描此PCI設備上的PCI選項ROM。
hot-plugged in the ExpressCard slot. This setting is only applicable if
ExpressCard Hot-Plug Resources is set to Enabled. The default
value for this setting is 4096 bytes of I/O space.
? Memory—This setting determines the amount of memory space, in
bytes, that will be reserved by the BIOS for PCI-PCI bridges that may
be hot-plugged in the ExpressCard slot. This setting is only applicable
if ExpressCard Hot-Plug Resources is set to Enabled. The default
value for this setting is 32 megabytes of memory.
? Pre-fetchable Memory—This setting determines the amount of
pre-fetchable memory space, in bytes, that will be reserved by the
BIOS for PCI-PCI bridges that may be hot-plugged in the ExpressCard
slot. This setting is only applicable if ExpressCard Hot-Plug
Resources is set to Enabled. The default value for this setting is
32 megabytes of pre-fetchable memory.
PXI Setup Menu
Use this menu to control and route certain signals on the PXI backplane.
Normally, you do not need to modify these settings. However, other
sections of this manual may indicate that modifications are necessary
and may lead to unpredictable behavior.
? APIC Routing—This item is valid only for Windows XP and 2000
and other modern operating systems. Select Enabled to initialize the
IOAPIC and local APIC in uniprocessor mode. Select Disabled to use
the legacy PIC for interrupt routing. The default setting is Enabled.
? PIRQx Routing—This setting selects the routing option for PXI/PCI
devices connected to PIRQx. This settings affects OSes that do not use
APIC routing. The default setting for all PIRQx options is IRQ10.
? Per-Slot Device Settings—This setting brings up the Per-Slot Device
Settings submenu. Refer to the Per-Slot Device Settings Submenu
section.
Per-Slot Device Settings Submenu
Use this menu to configure options that can be modified for individual PCI
devices in a PXI chassis.
Note Scanning for Option ROMs on devices behind a PCI bridge cannot be disabled.
PCI Device x Option ROM Scan—This setting selects whether PCI
device x will be scanned for an option ROM. Setting this option to Enabled
allows the BIOS to scan for a PCI option ROM on this PCI device. Setting
