主營產品
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
HONEYWELL 51401583-100輸出卡件
確保噴油器/推料器手柄處于向下位置。將NI PXI-8105與頂部和底部的卡導軌對齊系統控制器插槽的。
注意：插入NI PXI-8105時，不要升起噴射器/噴射器手柄。
除非手柄處于向下位置，否則模塊將無法正確插入，因此它不會干擾底盤上的噴油器導軌。
6.握住手柄，慢慢將模塊滑入機箱，直到手柄卡在噴油器/推料器導軌上。
7.升起噴油器/噴射器手柄，直到模塊牢固就位進入底板插座連接器。的前面板
NI PXI-8105應與機箱前面板齊平。擰緊頂部和底部的四個支架固定螺釘前面板，用于將NI PXI-8105固定至機箱。9.檢查安裝情況。
10.將鍵盤和鼠標連接到適當的連接器。如果你使用PS/2鍵盤和PS/2鼠標時，Y-splitter適配器是
可將兩者連接到單個USB連接器。提到圖4-1，Y型分離器電纜。
11.將DVI監視器視頻電纜連接到DVI連接器。如果你是使用VGA監視器時，請使用隨附的DVI到VGA適配器這是你的工具箱。
根據系統配置的要求將設備連接到端口。
13.接通顯示設備的電源。
14.打開機箱電源。如何從PXI機箱中卸下控制器
NI PXI-8105控制器的設計便于操作。刪除
從PXI機箱中取出單元，完成以下步驟：
1.關閉機箱電源。
2.拆下可能連接至控制器前面板的所有電纜。
3.擰下前面板上的支架固定螺釘。提到這些螺釘的位置見圖2-1。
4.按下噴油器/噴射器手柄。
5.將裝置滑出機箱。您可以在BIOS設置中更改NI PXI-8105配置設置。
BIOS是硬件和PC軟件之間的低級接口它在啟動系統時配置和測試硬件。這個
BIOS設置程序包括用于配置設置和啟用的菜單NI PXI-8105控制器功能。
大多數用戶不需要使用BIOS設置程序，如NI PXI-8105
控制器附帶了適用于大多數情況的默認設置配置。
警告：更改BIOS設置可能導致不正確的控制器行為，并且可能：
不可啟動控制器。如果發生這種情況，請按照恢復默認值的說明進行操作
系統CMOS部分中的設置。通常，除非您：絕對確定它做什么。
Make sure the injector/ejector handle is in its downward position.
Align the NI PXI-8105 with the card guides on the top and bottom
of the system controller slot.
Caution Do not raise the injector/ejector handle as you insert the NI PXI-8105.
The module will not insert properly unless the handle is in its downward position so
that it does not interfere with the injector rail on the chassis.
6. Hold the handle as you slowly slide the module into the chassis until
the handle catches on the injector/ejector rail.
7. Raise the injector/ejector handle until the module firmly seats
into the backplane receptacle connectors. The front panel of the
NI PXI-8105 should be even with the front panel of the chassis.Tighten the four bracket-retaining screws on the top and bottom of the
front panel to secure the NI PXI-8105 to the chassis.
9. Check the installation.
10. Connect the keyboard and mouse to the appropriate connectors. If you
are using a PS/2 keyboard and a PS/2 mouse, a Y-splitter adapter is
available to connect both to a single USB connector. Refer to
Figure 4-1, Y-Splitter Cable.
11. Connect the DVI monitor video cable to the DVI connector. If you are
using a VGA monitor, use the DVI-to-VGA adapter included with
your kit.
12. Connect devices to ports as required by your system configuration.
13. Power on the display device.
14. Power on the chassis.How to Remove the Controller from the PXI Chassis
The NI PXI-8105 controller is designed for easy handling. To remove the
unit from the PXI chassis, complete the following steps:
1. Power off the chassis.
2. Remove any cables that may be attached to the controller front panel.
3. Unscrew the bracket-retaining screws in the front panel. Refer to
Figure 2-1 for the location of these screws.
4. Press the injector/ejector handle down.
5. Slide the unit out of the chassis.You can change the NI PXI-8105 configuration settings in the BIOS setup.
The BIOS is the low-level interface between the hardware and PC software
that configures and tests your hardware when you boot the system. The
BIOS setup program includes menus for configuring settings and enabling
NI PXI-8105 controller features.
Most users do not need to use the BIOS setup program, as the NI PXI-8105
controller ships with default settings that work well for most
configurations.
Caution Changing BIOS settings may lead to incorrect controller behavior and possibly
an unbootable controller. If this happens, follow the instructions for restoring default
settings in the System CMOS section. In general, do not change a setting unless you are
absolutely certain what it does.
