P0926TL輸入輸出卡件
報警的默認優先級為3（參見第3.2節中的報警塊），這意味著必須確認報警以清除閃爍。報警也可配置為自清除。嘗試使用將報警優先級更改為4第2節中的配置路線圖或以下步驟：
1.按回車/退出配置。應顯示循環。
2.按兩次“向下”鍵，直到顯示屏上出現“視圖”。
3.按向右箭頭按鈕3次或轉動脈沖發生器旋鈕，直到顯示屏上出現編輯FB。
4.按下“下一步”。將顯示A/M。
5.按向右箭頭按鈕3次或轉動脈沖發生器旋鈕，直到顯示器上出現報警。
6.按下“下一步”以顯示RG PTR
7.按下向右箭頭按鈕或轉動脈沖發生器旋鈕，直到顯示器上出現A1 Previor。
8.按下步進鍵，在數字顯示器上顯示3。
9.要將報警1的優先級從3更改為4，請旋轉脈沖發生器旋鈕，直到數字顯示屏上出現4。
10.按存儲保存配置更改。
11.按ENTER/EXIT CONF返回正常操作。10.1.7標簽
按下標記按鈕。請注意，Loop01.*=P、S、V、X或Y）將在屏幕上滾動。為了改變標簽，
請參閱第2節中的配置路線圖或以下說明：
請注意，雖然標記有12個字符可用，但建議將循環名稱限制為6個字符
以便在正常操作期間顯示完整的標簽名稱。另外6個字符可以是：通過滾動標簽來顯示。正常操作期間顯示的字母數字的最后兩位數字為：
用于標識當前顯示的變量P、S、V、X或Y。
1.按回車/退出配置。將顯示循環。
2.按兩次“向下”鍵，直到屏幕上出現“視圖”。
3.按下向右箭頭按鈕或旋轉脈沖發生器旋鈕，直到顯示屏上出現編輯標簽。
4.按下“下一步”。LOOP01將以1位數字閃爍出現在顯示器上。使用脈沖發生器旋鈕：
更改閃爍字符的值，然后按存儲保存更改。使用箭頭按鈕移動到另一個角色。嘗試將標簽更改為TC101。
5.按ENTER/EXIT CONF返回正常操作模式。
6.按TAG可查看超過6個字符的標簽名稱。
10.1.8快速
在正常操作模式下，快速按鈕可用于單步通過任何
啟用此功能的功能塊。在FCO101中，SETPT功能塊具有快速設置功能
默認啟用。按下快速按鈕，注意您可以滾動瀏覽以下設定點功能：
斜坡接通/斷開、斜坡速率、目標設定點和加電設定點。漸變功能可以使用
斜坡時間或斜坡速率。默認情況下，使用率設置為“是”（參見第節中的“設置PT功能塊詳細信息3.2).
Alarms have a default priority of 3 (see Alarm block in Section 3.2), meaning that the alarms must be acknowledged
to clear the flashing. Alarms may also be configured as self clearing. Try changing the alarm priority to 4 using the
Configuration Road Map in Section 2 or the following steps:
1. Press ENTER/EXIT CONF. LOOP should be displayed.
2. Press STEP DOWN twice until VIEW appears on the display.
3. Press the right arrow button 3 times or turn the pulser knob until EDIT FB appears on the display.
4. Press STEP DOWN. A/M will be displayed.
5. Press the right arrow button 3 times or the turn pulser knob until ALARM appears on the display.
6. Press STEP DOWN to display RG PTR
7. Press the right arrow button or turn the pulser knob until A1 PRIOR appears on the display.
8. Press STEP DOWN to display 3 on the numeric display.
9. To change the priority of alarm 1 from 3 to 4, rotate the pulser knob until 4 appears on the numeric display.
10. Press STORE to save the configuration change.
11. Press ENTER/EXIT CONF to return to normal operation. 10.1.7 TAG
Press the TAG button. Note that Loop01.* (*= P, S, V, X or Y) will scroll across the screen. To change the tag,
refer to the Configuration Road Map in Section 2 or the following instructions:
Note that although 12 characters are available for the tag, it is suggested that loop names be limited to 6 characters
so that the complete tag name will be displayed during normal operation. The additional 6 characters can be
displayed by scrolling the tag. The last two digits of the alphanumeric displayed during normal operation will be
used to identify the variable currently being displayed, P, S, V, X or Y.
1. Press ENTER/EXIT CONF. LOOP will be displayed.
2. Press STEP DOWN twice until VIEW appears on display.
3. Press the right arrow button or the turn pulser knob until EDIT TAG appears on the display.
4. Press STEP DOWN. LOOP01 will appear on the display with the 1 digit flashing. Use the pulser knob to
change the value of the flashing character and press store to save the change. Use the arrow buttons to move to
another character. Try changing the TAG to TC101.
5. Press ENTER/EXIT CONF to return to normal operation mode.
6. Press TAG to view tag names longer than 6 characters.
10.1.8 QUICK
When in normal operation mode the QUICK button can be used to step through the QUICK SET parameters of any
function block which has this feature enabled. In FCO101, the SETPT function block has the QUICK SET feature
enabled as a default. Press the QUICK button and note that you can scroll through the following Setpoint features:
RAMP ON/OFF, Ramp RATE, TARGET setpoint, and POWER UP SETPOINT. The ramp feature can either use a
ramp TIME or a ramp RATE. USE RATE is set to YES as the default (see SETPT function block details in Section3.2).
