IC200PWB001A模塊卡件
米克羅優勢320型驅動器
MYCROADVANTAGE提供了一個LIL（320）驅動程序，該驅動程序將與本地儀器鏈路上的站通信
（LIL）。許多LIL產品（例如型號351和352）的標準預定義參數表在MYCROADVANTAGE可簡化配置。MYCROADVANTAGE 3.32版不包括模型352P/353/354是預定義的參數表。但是，當一個模型中最多配置三個控制回路時352P、353或354，使用模型351預定義參數表并配置循環中的ODC塊以通道8、13和18。由于控制器中的回路數據與351相同，因此該方法將起作用位于與a 351相同的相對偏移處。回路也可以單獨配置。有關配置可在MYCROADVANTAGE用戶手冊中找到。Modbus驅動程序
MYCROADVANTAGE提供了一個Modbus驅動程序，可通過單個COM與多達32個工作站通信
當使用Modbus驅動程序與352P、353或354型通信時，有一些注意事項。
?循環數據可用整數或浮點形式。當使用整數時，使用單個從而提高通信吞吐量。使用整數數據時，可以縮放范圍使用3：線性函數MX+B縮放。
?MODBUS。必須修改DAT文件。在[地址塊范圍]部分下，設置“UseDefault=0”，在[Address Size]部分下，設置“itChunkSize=48”和“WordChunkSize=60”。7.1.3 ProcessSuite
實時LIL I/O服務器
可選的LIL實時I/O服務器可用于與320型ICI（獨立計算機）通信接口）。320通過本地儀表鏈路（LIL）與具有LIL的其他站通信已安裝選項板。有關正確操作，請參閱LIL實時I/O服務器隨附的文獻。
通過使用全局數據優化LIL性能，特別是在每次掃描時更新的數據，如過程、設定點、閥門、回路狀態和報警I。僅使用單個參數請求獲取不需要的數據經常（例如，調整參數、范圍縮放）。
Modbus I/O服務器
Modbus I/O服務器隨過程套件提供，可用于與控制器通信。參考
Modbus I/O服務器操作詳細說明。某些參數設置至關重要。在主題中
定義，使用584/984從屬類型。將最大線圈讀數設置為48，最大寄存器讀數設置為60。
可以將最大線圈寫入設置為最小允許值8，并將寄存器寫入設置為2。
7.1.4 i|ware PC
Modbus OPC服務器
i|ware PC操作員界面軟件包括Modbus OPC服務器，當連接到控制器時，該服務器可以：
使用在站中配置的回路的數量和類型自動填充其數據庫。中使用的所有標記名
OPC數據庫將與本手冊中列出的相同。
MYCROADVANTAGE
Model 320 Driver
MYCROADVANTAGE provides a LIL(320) driver that will communicate with stations on a Local Instrument Link
(LIL). Standard, predefined parameter tables for many LIL products (e.g. Models 351 and 352) are within
MYCROADVANTAGE to simplify configuration. MYCROADVANTAGE release 3.32 does not include a Model
352P/353/354 predefined parameter table. However, when up to three control loops are to be configured in a Model
352P, 353 or 354, use the Model 351 predefined parameter table and configure the ODC blocks in the loops to
channels 8, 13, and 18. This method will work since the loop data in the controller is the same as a 351and is
located at the same relative offsets as in a 351. Loops can also be configured individually. Details on the
configuration can be found the MYCROADVANTAGE user manual. Modbus Driver
MYCROADVANTAGE provides a Modbus driver for communicating with up to 32 stations through a single COM
port. There are a few considerations when communicating with a Model 352P, 353 or 354 using the Modbus driver.
? Loop data is available as integer or floating point. When integer is used, more data is obtained with a single
command, thus improving the communication throughput. When integer data is used, ranges can be scaled
using 3:Linear function MX+B scaling.
? The MODBUS.DAT file must be modified. Under the section [Address Chunk Range], set “UseDefault=0”,
under section [Address Size], set “itChunkSize=48” and “WordChunkSize=60”.
7.1.3 ProcessSuite
RealTime LIL I/O Server
An optional LIL RealTime I/O Server is available to communicate with the Model 320 ICI (Independent Computer
Interface). The 320 communicates over the Local Instrument Link (LIL) with other stations that have the LIL
option boards installed. Refer to the literature provided with the LIL RealTime I/O Server for proper operation.
Optimize LIL performance by using Global Data, especially for data that is updated on each scan such as the
process, setpoint, valve, loop status, and alarm I. Use individual parameter requests only to obtain data not required
frequently (e.g. tuning parameters, range scaling).
Modbus I/O Server
A Modbus I/O Server comes with Process Suite and it can be used to communicate with the controller. Refer to the
Modbus I/O Server instructions for operating details. Certain parameter settings are critical. In the Topic
Definition, use the 584/984 slave type. Set the maximum coil reads to 48 and maximum register reads to 60.
Maximum coil writes can be set to the minimum allowed value of 8 and register writes to 2.
7.1.4 i|ware PC
Modbus OPC Server
The i|ware PC Operator Interface software includes a Modbus OPC server that when connected to the controller can
auto populate its database with the number and type of loops configured in the station. All tag names used in the
OPC database will be the same as listed in this manual.
