P0926EQ熱電阻模塊
DAM_功能塊計算輸入A和B，放大差分信號，并將與內部偏置和外部信號在輸入C。未使用的輸入設置為0.0。DID_功能塊轉換從LonWorks網絡上的單個或多個節點分成16個塊輸出，供內的其他功能塊使用控制器。最多可使用6個DID塊，最多可使用Lon網絡或內存上允許的節點數限制控制器的限制。塊的每次使用將分配一個唯一的全站ID（如DID02）。輸入連接為：通過“綁定”類型的每個輸出變量建立遠程節點設備中的SNVT_lev_disc（SNVT#22）用于DID功能塊中的每個網絡變量。這些當LonWorks選項板為：安裝在352P、353或354N控制器中。0 NV NUM參數啟用工作站的編號
已分配給輸入0。所有后續網絡變量為連續分配的。
每個功能塊輸出具有與其相關的模式。
這個模式可以是正常模式或強制模式。當使用能夠發送LIL或Modbus命令的PC，模式可以更改，強制狀態可以指定為高（1）或低（0）值。可通過網絡訪問的值包括：兩個開關輸入（N和F）和SPDT的位置方框圖中所示的開關。“0”的模式為正常，強制執行“1”。每個功能塊輸出還具有相關的質量狀態用它。當阻塞時，該狀態將變為高（1）確定其已與Lon節點失去通信。如果任何單獨的質量輸出都是高質量的狀態塊輸出也將為高。當可選以太網通信板10為：安裝在控制器中。它啟用控制器通過以太網。
最多可提供32個DIE_塊。積木是按順序分配，控制器范圍，每個使用數字數據是封裝為16位的開/關數據單詞該數據被扇出至塊輸出D0–DF。IP地址參數用于配置源設備的IP地址。MB地址參數允許Modbus地址為：配置。當連接到其他西門子時摩爾控制器，Modbus地址設置為1。
在某些情況下，其他設備可能使用不同的地址或通過Modbus TCP/IP網關時，Modbus網絡可能有多個設備，每個設備具有唯一的地址。
DAM_ function blocks compute the difference between
inputs A and B, amplify the difference signal, and sum the
resultant with an internal BIAS and an external signal at
input C. Unused inputs are set to 0.0.DID_ function blocks convert 16 on/off signals received from
a single or multiple nodes on the LonWorks network into 16
block outputs for use by other function blocks within the
controller. A maximum of 6 DID blocks can be used, up to the
limit of nodes allowed on the Lon network or the memory
limit of the controller. Each use of the block will be assigned a
unique station wide ID (e.g. DID02). Input connections are
established by ‘binding’ each output variable of type
SNVT_lev_disc (SNVT #22) in the remote node devices to
each network variable in the DID function block. These
blocks will be available when the LonWorks option board is
installed in a 352P, 353, or 354N controller.
The 0 NV NUM parameter enables the number that the station
has assigned to input 0. All subsequent network variables are
assigned consecutively.
Each function block output has a mode associated with it. The
mode can be either NORMAL or FORCED. When using a
PC capable of sending LIL or Modbus commands, the mode
can be changed and the forced state can be assigned a high (1)
or low (0) value. The values accessible over the network are
the two switch inputs (N and F) and the position of the SPDT
switch illustrated in the block diagram. A mode of ‘0’ is
Normal and ‘1’ is Forced.
Each function block output also has a quality status associated
with it. This status will go high (1) when the block
determines it has lost communication with the Lon node. If
any of the individual quality outputs are high the Quality
Status block output will also be high.
DIE_ function blocks are available when the
optional Ethernet communication board10 is
installed in the controller. It enables the controller
to read digital data from other stations over the
Ethernet network.
Up to 32 DIE_ blocks are available. Blocks are
assigned in sequence, controller wide, with each
use. Digital data is On/Off data packed into a 16-bit
word. This data is fanned out to block outputs D0 –
DF.
The IP ADRES parameter is used to configure the
IP address of the source device. The MB ADRES
parameter allows a Modbus address to be
configured. When connecting to other Siemens
MOORE controllers, the Modbus address is set to 1.
In some cases, other devices may use a different
address or when going through a Modbus TCP/IP gateway a Modbus network may have multiple devices, each
having a unique address.
