BENTLY 149992-01位移監測器
產品支持可從客戶服務中心（即北美的技術支持小組或
亞洲或歐洲的技術信息中心（TIC）。每個地區都有一個客戶服務中心，提供：
就與產品功能、應用和集成相關的技術問題提供直接電話支持。
區域聯系信息如下。您的區域技術支持小組或TIC是第一個：
尋求產品支持信息時請致電。打電話時，準備好以下信息很有幫助：
?產品零件號或型號和版本
?如果產品操作有問題：
-故障是否為間歇性故障
-問題發生前執行的步驟
-顯示任何狀態消息、錯誤消息或LED指示
-安裝環境、設備交付和搬運
1.4.1工廠裝運
裝運前，對控制器進行全面測試和檢查，以確保其正常運行。然后將其包裝為：
運輸大多數配件單獨裝運。
1.4.2貨物的接收
在交付時檢查每個紙箱是否存在可能的外部損壞。任何可見的損壞應立即修復記錄在承運人的交貨單副本上。
仔細打開每個紙箱的包裝，并對照隨附的裝箱單檢查內容。檢查每個項目是否存在任何
可能或可能未伴隨外部紙箱損壞的隱藏損壞。
如果發現某些項目已損壞或丟失，通知工藝儀表部門
西門子能源和自動化立即提供詳細信息。此外，必須向承運人要求對受損物品及其裝運紙箱進行現場檢查。
1.4.3儲存
如果控制器要在安裝前儲存一段時間，請查看第14節中的環境規范型號名稱和規格。
裝運時，MPU控制器板實時時鐘跳線（W7或W8）設置為最大限度延長電池壽命。如果跳線已設置為啟用熱/熱啟動，或確認跳線設置正確，請參閱第11節
維護并將跳線設置為存儲。典型裝運內容
下面列出的項目通常包括在裝運中，可能會發生變化。
1.摩爾353過程自動化控制器，每個訂單的型號，數量。1.
2.功率輸入和量程電阻器套件，PN 16354-30，數量。1.
描述數量
電阻器，250?, 0.1%，3W，WW3套管3
接頭6上的壓接
套件安裝說明1
3.安裝夾套件，無零件號，數量。1.
內容：2個安裝夾和2個8-32 x 1螺釘（零件號見本手冊后面的零件清單）
4.I/O擴展器板套件
PN16353-52 I/O擴展器板套件-當摩爾353與已訂購擴展板選項1。
PRODUCT SUPPORT
Product support can be obtained from a customer service center (i.e. Technical Support Group in North America or
a Technical Information Center (TIC) in Asia or Europe). Each region has a customer service center that provides
direct telephone support on technical issues related to the functionality, application, and integration of the product.
Regional contact information is provided below. Your regional Technical Support Group or TIC is the first place to
call when seeking product support information. When calling, it is helpful to have the following information ready:
? Product part number or model number and version
? If there is a problem with product operation:
- Whether or not the problem is intermittent
- The steps performed before the problem occurred
- Any status message, error messages, or LED indications displayed
- Installation environment EQUIPMENT DELIVERY AND HANDLING
1.4.1 Factory Shipment
Prior to shipment, a controller is fully tested and inspected to ensure proper operation. It is then packaged for
shipment. Most accessories are shipped separately.
1.4.2 Receipt of Shipment
Inspect each carton at the time of delivery for possible external damage. Any visible damage should be immediately
recorded on the carrier’s copy of the delivery slip.
Carefully unpack each carton and check the contents against the enclosed packing list. Inspect each item for any
hidden damage that may or may not have been accompanied by exterior carton damage.
If it is found that some items have been damaged or are missing, notify the Process Instrumentation Division of
Siemens Energy and Automation immediately and provide full details. In addition, damages must be reported to the
carrier with a request for their on-site inspection of the damaged item and its shipping carton.
1.4.3 Storage
If a controller is to be stored for a period prior to installation, review the environmental specifications in Section 14
Model Designation and Specifications.
As shipped, the MPU Controller board Real Time Clock Jumper (W7 or W8) is set to maximize battery life. If the
jumper has been set to enable Hot/Warm Start, or to confirm that the jumper is properly set, refer to Section 11
Maintenance and set the jumper for storage. Typical Shipment Contents
The items listed below are those typically included in a shipment and are subject to change.
1. Moore 353 Process Automation Controller, model number per order, qty. 1
2. Power Input and Range Resistor Kit, PN 16354-30, qty. 1
DESCRIPTION QUANTITY
Resistor, 250?, 0.1%, 3W, WW 3
Sleeving 3
Crimp-On Connector 6
Kit Installation Instruction 1
3. Mounting Clip Kit, no part number, qty. 1
Contents: 2 Mounting Clips and 2, 8-32 x 1 Screws (see the Parts List at back of this manual for part numbers)
4. I/O Expander Board Kits
PN16353-52 I/O Expander Board Kit - The I/O Expander Board is factory installed when a Moore 353 with
Expansion Board option 1 is ordered.
