FALCON SG2K-1T數控模塊
只有在以下情況下，工程卡按鈕功能才會工作：選擇通道卡。見第3.3節。
在工程卡上未安裝工程鑰匙的情況下，以下情況
工程卡按鈕將不可用：阻止
零跨度
第一跨
如果按下這些按鈕中的任何一個，將顯示鎖定符號（）
在所選頻道卡信息顯示屏上短暫顯示。
4.2超時
在沒有工程鑰匙的情況下操作工程卡時
安裝有30秒的超時時間。如果沒有按鈕
在超時時間內按下，所選通道卡將自動取消選擇。
4.3條形圖顯示在沒有工程鑰匙的情況下操作工程卡時安裝后，所選通道的條形圖顯示將繼續指示
可用工程運行期間的實際氣體讀數卡功能。
4.4催化傳感器橋電流
與胎圈mA按鈕相關的操作僅適用至催化通道卡。使用其他類型操作此按鈕所選通道卡的數量沒有影響，并且警告消息（XXXX）將顯示一小段時間。
要進入催化傳感器橋電流操作，請按跟隨：（1） 按住所需的通道卡復位/選擇按鈕約1.5秒，直到出現所選圖標在頻道顯示（2）上，按下珠子mA按鈕，然后選擇通道卡顯示將指示已配置的網橋現在的例如200mA。
（3） 按下拒絕（）按鈕或等待30秒以退出胎圈mA模式。
4.5查看報警級別設置
報警按鈕的操作允許查看
每個報警的報警閾值點和報警類型（上升或下降）設定點A1、A2和A3。
要進入報警視圖操作，請執行以下操作：
（1） 按住所需的通道卡復位/選擇按鈕約1.5秒直到所選圖標出現在頻道顯示器上。
（2） 按下報警按鈕，然后選擇
通道卡顯示器將指示A1級報警為：相反地指示。
注：向上箭頭A表示上升報警，向下箭頭A表示下降報警
箭指示下降警報。
The Engineering Card push-button functions will only operate if a
channel card is selected. See Section 3.3.
Without the Engineering Key fitted to the Engineering Card, the following
Engineering Card push-buttons will not be available:
Inhibit
Zero
Span
1st Span
If any of these push-buttons are pushed, a locked symbol ( ) will be
briefly displayed on the selected channel card message display.
4.2 Timeout
When operating the Engineering Card without an Engineering Key
fitted there is a timeout period of 30 seconds. If no push-buttons are
pressed within the timeout period, the selected channel card will
automatically be deselected.
4.3 Bar Graph Display
When operating the Engineering Card without an Engineering Key
fitted, the selected channel's bar graph display will continue to indicate
the actual gas reading during the operation of the available Engineering
Card functions.
4.4 Catalytic Sensor Bridge Current
The operation associated with the BEAD mA push-button only applies
to catalytic channel cards. Operating this push-button with other types
of channel cards selected has no effect and the warning message
(XXXX) is displayed for a short time.
To enter the catalytic sensor bridge current operation, proceed as
follows:
(1) Push and hold the required channel card RESET/SELECT pushbutton for approximately 1.5 seconds until the selected icon appears
on the channel display(2) Push the BEAD mA push-button and the selected
channel card display will indicate the configured bridge
current. eg. 200mA.
(3) Push the reject ( ) push-button or wait 30 seconds to
exit the Bead mA mode.
4.5 View Alarm Level Settings
The operation of the ALARMS push-button allows the viewing of the
alarm threshold point and alarm type (rising or falling) for each alarm
set point A1, A2 and A3.
To enter the alarm view operation, proceed as follows:
(1) Push and hold the required channel card RESET/
SELECT push-button for approximately 1.5 seconds
until the selected icon appears on the channel display.
(2) Push the ALARMS push-button and the selected
channel card display will indicate the A1 level alarm as
indicated opposite.
Note: The up arrow A indicates a rising alarm while the down A
arrow
indicates a falling alarm.
