国产精品久久二区二区,熟女少妇内射日韩亚洲,久久亚洲国产成人精品无码区,GOGO熟女少妇大尺度

您的瀏覽器版本過低,為保證更佳的瀏覽體驗,請點擊更新高版本瀏覽器

以后再說X

歡迎訪問瑞昌明盛自動化設備有限公司網站!

圖片名

全國訂購熱線:
+86 15270269218E-mail:xiamen2018@foxmail.com

ABB >>

A-B>>

GE>>

BENTLY>>

BENTLY 330100-90-00

BENTLY 330100-90-00

BENTLY 330100-90-00監測器模塊檢查執行器是否短路或接地通過拆下接線端20和21.停止原動機。合上開關端子18,將端子23短接至24。檢查對于端子20和21處的18至22伏正向控制,0至1伏反向控制。檢查端子28處是否至少有1個VRM以及最小值的至少5%額定速度和頻率范圍。初始速度設置過低開始控制可能是錯誤的速度范圍。檢查轉速傳感器頻率與控制部件號。速度設置可能是:低于起動速度。控...

  • 功能特性
  • 參數規格
  • 視頻
  • 應用案例
  • 下載

BENTLY 330100-90-00

    BENTLY 330100-90-00監測器模塊


    檢查執行器是否短路或接地

    通過拆下接線端20和21.停止原動機。合上開關

    端子18,將端子23短接至24。檢查對于端子20和21處的18至22伏正向控制,0至1伏反向控制。

    檢查端子28處是否至少有1個VRM

    以及最小值的至少5%額定速度和頻率范圍。初始速度設置過低

    開始控制可能是錯誤的速度范圍。

    檢查轉速傳感器頻率與控制部件號。速度設置可能是:低于起動速度。控制應設置為額定速度。增加額定值速度設置為順時針。

    通知


    如果調整額定速度設置

    順時針方向不產生正確的輸出,返回額定速度設置至正常啟動位置滿逆時針方向的

    低怠速設置可能:

    設置得太低。調整低怠速電位計順時針方向的最小燃油觸點打開。看見中的“最小燃料接觸”

    第二章。

    檢查T 17。最小燃油接觸必須為正常運行時關閉。檢查20到從端子17(+)到15(-)的40 Vdc。

    速度傳感器信號未清除速度信號電路故障。

    檢查接線是否正確連接。檢查正確安裝的護罩。

    速度傳感器間隔不正確檢查


    端子28和29處的電壓至少為1.0 Vac在起動期間。如果小于1.0VAC,磁性拾取器可能間隔太遠從齒輪。確保沒有金屬撿拾器末端的碎屑。

    如果不存在電壓,磁傳感器可能開路或短路。制作導線檢查電阻與控制斷開。應該是100至300?.

    故障轉速信號電路可能被禁用

    通過連接端子16(或端子0 on高壓控制)連接到端子18。

    警告做好應急準備起動發動機時停機,渦輪機或其他類型的原動機防止失控或超速可能造成人身傷害,損失生命或財產損失。

    Check for shorted or grounded actuator

    leads by removing wires to terminals 20 and

    21. Stop prime mover. Close the switch on

    terminal 18, short terminal 23 to 24. Check

    for 18 to 22 volts at terminals 20 and 21 for

    forward acting controls, and 0 to 1 volt for

    reverse acting controls.

    Check for at least 1 Vrms at terminals 28

    and 29, and at least 5% of the minimum

    rated speed frequency range.

    Speed setting too low on initial

    start.

    Control may be the wrong speed range.

    Check speed sensor frequency versus

    control part number. Speed setting may be

    lower than cranking speed. Control should

    be set for rated speed. Increase RATED

    SPEED setting clockwise.

    NOTICE

    If adjusting RATED SPEED setting

    clockwise does not produce the correct

    output, return RATED SPEED setting to

    normal start position—full

    counterclockwise.

    LOW IDLE SPEED setting may

    be set too low.

    Adjust LOW IDLE SPEED potentiometer

    clockwise.

    Minimum Fuel contact open. See

    “Minimum Fuel Contact” in

    Chapter 2.

    Check T 17. Minimum-fuel contact must be

    closed for normal operation. Check for 20 to

    40 Vdc from terminal 17 (+) to 15 (–).

    Speed sensor signal not clearing

    failed speed signal circuit.

    Check wiring for proper connection. Check

    shields for proper installation.

    Speed sensor not spaced properly—check

    for at least 1.0 Vac at terminals 28 and 29

    during cranking. If less that 1.0 Vac,

    magnetic pickup may be spaced too far

    from gear. Make sure there are no metal

    chips on end of pickup.

    If no voltage is present, magnetic pickup

    may be open-circuited or shorted. Make

    resistance check with the leads

    disconnected from control. Should be about

    100 to 300 ?.

    Failed speed-signal circuit may be disabled

    by connecting terminal 16 (or terminal 0 on

    high voltage controls) to terminal 18.

    WARNING

    Be prepared to make an emergency

    shutdown when starting the engine,

    turbine, or other type of prime mover, to

    protect against runaway or overspeed

    with possible personal injury, loss of

    life, or property damage. 


    品牌:BENTLY

    型號:330100-90-00

    產地:美國

    質保:365天

    成色:全新/二手

    發貨方式:快遞發貨


圖片名 客服

在線客服 客服一號