IC697PCM711燃機通用卡件
將器件拆下并放置在紫外線燈下。任何液體滲透都會在染料發出的熒光下無所遁形。為提高開關電源產品的可靠性，開關電源會設計輸出過壓保護功能，防止產品內部的某個元器件損壞后，導致輸出電壓升高。而電源后端的負載只能承受一定的電壓大小，一旦輸出電壓升高，會損壞電源后端的負載。為防止此問題發生，開關電源都會設計輸出過壓保護電路，從而提升系統可靠性工作。在電路中，一旦下拉電阻R2短路，根據計算公式知，Vo電壓會變?yōu)闊o(wú)窮大，一旦輸出電壓升高到一定值后，則會損壞電源的負載，導致系統燒壞。
IC697PCM711燃機通用卡件為防止此問題發生，在電路中增加輸出過壓保護電路。如圖2所示是輸出過壓保護電路的原理簡圖之一，其工作原理如下：一旦下拉電阻R2短路，輸出電壓往上升高，一旦輸出電壓升高到穩壓二極管ZD1的擊穿電壓后，穩壓二極管工作，把輸出電壓鉗位在穩壓二極管的擊穿電壓值，防止輸出電壓繼續上升到無窮大，此時輸出電壓值被穩壓二極管鉗位在擊穿電壓值大小，不會再上升。穩壓二極管ZD1的規格參數值選型一般選取大于輸出電壓值2-3V即可。過壓保護電路適用于輸出功率小于75W以下的小功率電源產品中，對于大功率電源產品，輸出過壓保護電路的設計是控制原邊IC的工作，實現輸出過壓保護。當產品過壓保護時，輸出電壓呈現打嗝輸出模式或是直接關斷輸出電壓，防止輸出功率過高損壞后級負載系統。由于電路比較復雜，在此不做原理說明。開關電源的輸出過壓保護電路的工作原理和作用。部分客戶在使用開關電源時，負載端存在輸出電壓倒灌現象，損壞開關電源產品或是導致開關電源產品無法正常工作。開關電源的過壓保護功能和電源防倒灌電壓功能是兩種不同的情況，不能混為一談。開關電源的過壓保護功能是電源向外的保護功能，防止外部負載系統損壞；而開關電源的防倒灌能力是指外部電壓對開關電源的影響力，避免產品的輸出端存在倒灌電壓時損壞開關電源，在此需要特別區分這兩種情況。在開關電源中，根據倒灌電壓產生的機理，輸出端存在反灌電壓的原因有如下幾種情況：
1、系統在不同的輸出電壓之間切換時會存在高壓電壓倒灌到低壓電源中，此問題在直流充電樁設備中比較常見；
2、開關電源的負載是感性負載，負載工作時會產生感應電動勢，感應電動勢生成的電壓倒灌到開關電源的輸出端；Sensors and transmitters such as motor current, water pump shaft temperature, motor temperature, drainage pipe flow, etc. are mainly used to monitor the operating conditions of water pumps and motors, and alarm when the limit is exceeded, so as to avoid damage to water pumps and motors. The digital input module of PLC collects various switching signals into PLC as the condition and basis of logic processing to control the start and stop of drainage pump. In the process of data acquisition, the processing of analog signal is to convert analog signal into digital signal (a/d conversion), and its conversion speed is determined by the sampling law. Generally, the sampling frequency should be more than 2 times of the highest frequency component in the analog signal, so that the accuracy of the a/d transformation can be completely restored to the original analog signal accuracy. The accuracy of a/d conversion depends on the number of bits of the a/d converter. For example, when the 5V voltage is required to be converted with the accuracy of 5mv, the accuracy is 5mv/5v=0.1%, that is, when the 1/1000 decimal 1000 is expressed in binary, it is required to be 10 bits, while the resolution of the a/d module used in this system is 16bit, and its accuracy is more than ± 0.05%, which
