TRICONEX 17-550544-001B工控卡件，FTA-544說明書文檔
SRTP連接保持打開狀態IP地址更改后以太網接口不會在之前終止所有打開的SRTP連接更改其IP地址。一旦本地IP地址發生更改，任何現有的TCP連接無法正常終止。這會留下SRTP連接打開，直到其底層TCP連接超時。如果更快需要恢復SRTP連接，修改“wkal_idle”高級用戶參數將TCP保持活動計時器降低到所需的最大時間用于保持斷開的連接。
TRICONEX 17-550544-001B工控卡件參見TCP/IP以太網通信對于PACSystems，請參閱GFK-2224以了解詳細信息。用于生成EGD的CPU時間時間標記通過CHTIME命令更改以太網接口時間不會影響從該以太網接口生成的EGD交換中的時間戳值。這個EGD時間戳值反映當前CPU時間。90-70系列產品和90-30系列CPU364、EGD時間戳取自以太網接口并且確實反映了CHTIME修改。ENIU運行模式期間的過時數據EGD存儲在運行20 ENIUs的大型PPS系統中，當執行運行模式存儲時這將刪除10個ENIUs的EGD交換，另一個ENIUs將看到其交換上的狀態指示RMS期間的消耗超時。在完成RMS后，交換機正常運行。Internet Explorer 8可能需要使用Web時設置更改RX7i頁面使用Internet Explorer 8時，可能需要禁用彈出窗口阻止程序使用隨RX7i以太網固件提供的網頁。要禁用彈出窗口阻止程序，在Internet Explorer工具欄中，選擇工具->彈出窗口攔截器->關閉彈出攔截器注意：如果你安裝了谷歌工具欄，谷歌彈出窗口攔截器可能會也必須禁用。使用Internet時，可能還需要禁用配置腳本瀏覽器8。在工具欄中選擇“Internet選項”。在“Internet選項”對話框中單擊“連接”選項卡，單擊“LAN設置”按鈕，并確保該框在“自動檢測設置”旁邊有一個復選框。如果沒有，請單擊該框
在“自動檢測設置”旁啟用此設置。
SRTP connections remain open
after IP address changed
The Ethernet Interface does not terminate all open SRTP connections before
changing its IP address. Once the local IP address has changed, any existing open
TCP connections are unable to normally terminate. This can leave SRTP
connections open until their underlying TCP connections time out. If quicker
recovery of the SRTP connection is needed, modify the “wkal_idle” Advanced User
Parameter to reduce the TCP keep alive timer down to the desired maximum time
for holding open the broken connection. Refer to TCP/IP Ethernet Communications
for PACSystems, GFK-2224, for details.
CPU Time Used for Produced EGD
Timestamps
Changing the Ethernet interface time via the CHTIME command does not affect the
timestamp value within EGD exchanges produced from this Ethernet interface. The
EGD timestamp value reflects the current CPU time. In Series 90-70 products and
the Series 90-30 CPU364, EGD timestamps are taken from the Ethernet interface
and do reflect CHTIME modifications.
ENIU Stale Data During Run Mode
Store of EGD
In a large PPS system running 20 ENIUs, when a Run-mode Store is performed
that deletes the EGD exchanges for 10 of the ENIUs, the other ENIUs will see the
status on their exchanges indicate consumption timeouts during the RMS. At the
completion of the RMS, the exchanges operate normally.
Internet Explorer 8 may require
setting changes when using Web
pages on RX7i
It may be required to disable the pop-up blocker when using Internet Explorer 8
with the Web pages supplied with the RX7i Ethernet firmware. To disable the
pop-up blocker, in the Internet Explorer toolbar, select Tools->Pop-up
Blocker->Turn Off Pop-up Blocker
Note: If you have the Google toolbar installed, the Google pop-up blocker may
also have to be disabled.
It may also be required to disable configuration scripts when using Internet
Explorer 8. In the Toolbar select Internet Options. In the Internet Options dialog box
click the “Connections” tab, click the “LAN settings” button, and make sure the box
beside “Automatically detect settings” has a check in it. If it does not, click the box
next to “Automatically detect settings” to enable this setting.
