6ES193-1CL00-0XA0工控卡件,產品重量
按下并釋放MVME187前面板重置開關啟動系統重置。
如果處理器停止運行，或者出現錯誤，則必須使用重置環境丟失（向量表被破壞，堆棧損壞，等等）。? 冷復位和熱復位模式可用。? 默認情況下，187Bug處于冷模式。
冷復位期間：1、進行整個系統初始化，就像MVME187剛剛通電。
2、所有靜態變量（包括磁盤設備和控制器）參數）恢復到其默認狀態。
6ES193-1CL00-0XA0工控卡件3、清除斷點表和偏移寄存器。4、目標寄存器無效。
5.清除輸入和輸出字符隊列。6、車載設備（計時器、串行端口等）重置，以及
7.將前兩個串行端口重新配置為其默認值狀態在熱復位期間：1.187Bug變量和表被保留，以及目標狀態寄存器和斷點。
中止通過按下并釋放上的Abort開關來調用AbortMVME187前面板。
如果程序被捕獲，則應使用中止來重新獲得控制在循環中等。每當在運行目標代碼時調用abort時（用戶程序），捕捉處理器狀態的“快照”，并存儲在目標寄存器中。因此，中止是最重要的在終止正在運行的用戶程序時適用已調試。目標IP、注冊內容等有助于精確定位故障中止序列按下并釋放中止開關可執行以下操作：1、生成一個本地板條件，該條件可能會中斷處理器（如果啟用）。2、在屏幕上顯示目標寄存器，反映按下中止開關時的機器狀態。
3.刪除用戶代碼中安裝的任何斷點，并保持?jǐn)帱c(diǎn)表不變。
4.將控制返回給調試器。
Pressing and releasing the MVME187 front panel RESET switch
initiates a system reset.
Reset must be used if the processor ever halts, or if the 187Bug
environment is ever lost (vector table is destroyed, stack corrupted,
etc.).
? COLD and WARM reset modes are available.
? By default, 187Bug is in COLD mode.
During COLD reset:
1. A total system initialization takes place, as if the MVME187
had just been powered up.
2. All static variables (including disk device and controller
parameters) are restored to their default states.
3. The breakpoint table and offset registers are cleared.
4. The target registers are invalidated.
5. Input and output character queues are cleared.
6. Onboard devices (timer, serial ports, etc.) are reset, and
7. The first two serial ports are reconfigured to their default
state.
During WARM reset:
1. The 187Bug variables and tables are preserved, as well as the
target state registers and breakpoints.
Abort
Abort is invoked by pressing and releasing the ABORT switch on the
MVME187 front panel.
Abort should be used to regain control if the program gets caught
in a loop, etc. Whenever abort is invoked while running target code (a user
program), a “snapshot” of the processor state is captured and
stored in the target registers. For this reason, abort is most
appropriate when terminating a user program that is being
debugged. The target IP, register contents, etc., help to pinpoint the
malfunction.
Abort Sequence
Pressing and releasing the ABORT switch does the following:
1. Generates a local board condition which may interrupt the
processor if enabled.
2. Displays the target registers on the screen, reflecting the
machine state at the time the ABORT switch was pressed.
3. Removes any breakpoints installed in the user code and
keeps the breakpoint table intact.
4. Returns control to the debugger.
