IS220PVIBH1AL電氣模塊,IS220PVIBH1AL使用數量
完整的設置由許多主菜單和子菜單組成。下表顯示了逐步完成整個設置時，按外觀順序排列主菜單。桌子也概述了您可以在以下每個主菜單中進行的選擇和參數設置。完整的設置順序在第3.12節中進行了描述。本節提供了一個分步說明，詳細介紹了所有可用的帶有相關參數、數據和設置的設置菜單。使用上下鍵從列表中選擇語言[ZZ]、單位[ZZZ]和小數位數[Z]。
IS220PVIBH1AL電氣模塊菜單SetWebWidth僅在選擇單位N/m、kN/m、kg/m或pli時可用。設置語言以下語言可用：?英語、德語、意大利語、法語、葡萄牙語和日語3.12.1.2機組可以設置以下單位：?N（牛頓）?kN（千牛頓）?kg（千克如果所選單位為N/m、kN/m、kg/m或pli，則需要設置腹板寬度。默認腹板寬度為2m（78740英寸）。3.12.1.3設置腹板寬度菜單SetWebWidth僅在所選單位為N/m、kN/m、kg/m或物價指數。默認腹板寬度為2m（78740英寸）。格式為XX。如果寬度以米和XXXX輸入，則為XXX。XX如果輸入寬度英寸最大腹板寬度為50m（1968,5英寸）3.12.1.4集合小數可以在此菜單中設置顯示的小數位數。可以設置小數位數根據稱重傳感器標稱負載和表示單元，將其設置為0-5之間的數字。第4.6節進一步解釋了集合小數函數。在菜單系統定義中，必須設置以下內容：稱重傳感器梳（稱重傳感器組合）–一卷（稱重傳感器A和B）–兩個輥（輥1連接到A和B；輥2連接到C和D）–分段滾動?收益計劃（包裹收益計劃）。可用于一卷、兩卷（僅第1卷）和分段滾動。
The complete setup is built up by a number of main and sub menus. The table below shows the
main menus in order of appearance when stepping through the complete setup. The table also
gives an overview of the selections and parameter settings you can do below in each main menu.
The complete setup sequence is described in Section 3.12This section provides a step-by-step description with detailed information about all available
setup menus with related parameters, data and settings.Use up and down keys to select language [ZZ], unit [ZZZZ] and number of decimals [Z] from list.
The menu SetWebWidth will only be available when unit N/m, kN/m, kg/m or pli is selected.Set Language
The following languages are available:
? English, German, Italian, French, Portuguese and Japanese
3.12.1.2 Set Unit
The following units can be set:
? N (Newton)
? kN (kiloNewton)
? kg (kilogramIf the selected unit is N/m, kN/m, kg/m or pli, the Web Width needs to be set.
Default Web Width is 2m (78,740 inch).
3.12.1.3 Set Web Width
The menu SetWebWidth will only be available when the selected unit is N/m, kN/m, kg/m or
pli.
Default Web Width is 2m (78,740 inch).
The format is XX.XXX if the width is entered in meter and XXXX.XX if the width is entered in
inch. Maximum Web Width is 50m (1968,5 inch)
3.12.1.4 Set Decimals
The number of displayed decimals can be set in this menu. The number of decimals may be set
to a number between 0 - 5 depending on the load cell nominal load and presentation unit.
Set decimals function is further explained in Section 4.6.In menu SystemDefinition the following must be set:
? LoadCellComb (load cell combination)
