P0924JH端子模塊,P0924JH使用配置教程
讀取和寫入數據表的Modbus命令需要一個參考（起點），并且有些情況下，分數是多少。提供的Modbus命令參考和PLC數據表
PLC中RTU模塊訪問的元件不一定等于以下所述。
最初，Modbus協議僅用于訪問4個不同的數據表，并且寫入數據量有限數據RTU模塊通過執行參考映射來擴展這些限制。RTU模塊包含PLC數據表的地圖，并為每個數據分配一系列相關的Modbus參考桌子因此，用戶只需簡單地通過一個Modbus命令即可訪問多個PLC數據表
P0924JH端子模塊更改參考。上表描述了Modbus參考的細分區域訪問適當?shù)臄?shù)據表。每個型號的PLC CPU包含每個數據表的不同最大點數。在期間在RTU模塊初始化時，詢問CPU的每個數據表的大小。應該aModbus參考，并在該命令后立即撥打號碼其中n=數字0到9，符號#和*，可能包括下面列出的撥號修飾符。調制解調器將以撥號修改器確定的方式撥打指定的號碼。表盤
除；修飾符，必須出現在字符串的末尾。在本例中，調制解調器脈沖撥打9位數字，等待撥號音，然后撥號音撥打數字然后撥打123-4567。最后，調制解調器在結束后返回到命令模式已撥打數字。P修飾符使調制解調器以每秒10個脈沖的固定速率進行脈沖或旋轉撥號。T修飾符使調制解調器使用DTMF（雙音多頻）信號撥號（與“，”修飾符使調制解調器暫停。例如，撥打長途服務時調制解調器必須首先撥打本地接入號碼，然后暫停足夠長的時間，以接收服務撥號音。“，”在從PBX系統撥號時也很有用，因為兩次請求之間可能會花費相當長的時間
并獲得第二撥號音或“外部”線路。
@modifier使調制解調器等待一個或多個響鈴3秒，然后等待5秒
在處理撥號字符串中的下一個符號之前靜音。這在訪問以下系統時非常有用：
不要提供撥號音。
The Modbus commands which read and write to data tables require a reference (starting point) and, in
some cases, the number of points. The Modbus command reference provided and the PLC data table
element accessed by the RTU module in the PLC are not necessarily equal as described below.
Originally, the Modbus protocol was only meant to access 4 different data tables with limited writing of
data. The RTU module expands these limitations by performing reference mapping. The RTU module
contains a map of PLC data tables and assigns a range of associated Modbus references to each data
table.Therefore, the user can access more than one PLC data table with a single Modbus command by simply
changing the reference. The tables above describe the sub-divided regions of the Modbus reference to
access the appropriate data table.Each model of the PLC CPU contains a different maximum number of points for each data table. During
initialization of the RTU module, the CPU is interrogated for the size of each of its data tables. Should a
Modbus reference andDial the Number Immediately Following this Command
Where n = digits 0 to 9, the symbols # and *, and may include the dial modifiers listed below.
The modem will dial the number specified in the manner determined by the dial modifiers. The dial
modifiers may appear anywhere within the dial string with the exception of the ; modifier which must
appear at the end of the string.In this example the modem pulse dials a 9-digit number, waits for a dial tone, then tone dials the digits
713. It then dials the number 123-4567. Finally, the modem returns to the command mode after the final
digit has been dialed.
The P modifier causes the modem to pulse or rotary dial at a fixed rate of 10 pulses per second.
The T modifier causes the modem to dial using DTMF (Dual-tone multifrequency) signals (the same as
those used by “touch-tone” telephones)The "," modifier causes the modem to pause. When dialing a long distance service, for example, the
modem must first dial the local access number, then pause long enough for the services dial tone. The ","
is also useful when dialing from a PBX system where considerable time may elapse between requesting
and getting a secondary dial tone or "outside" line.
The @ modifier causes the modem to wait for 3 seconds for one or more rings followed by 5 seconds of
silence before processing the next symbol in the dial string. This is useful when accessing systems that
do not provide a dial tone.
