KOLLMORGEN E33NRHA-LNN-NS-00電機,E33NRHA-LNN-NS-00使用方法
輸入具有二階低通硬件濾波器和數字濾波器單個時間常數為0.5至32 ms。
除了車載輸入/輸出，直接輸入/輸出系統支持S200輸入/輸出。最多八個外部輸入/輸出單元可以直接插入安裝在控制器上DIN導軌和其他八個輸入/輸出單元可以通過TK210電纜連接（長度0.5、1.0、，或2.5 m）和200-AIO適配器。一排輸入/輸出單元可以使用200-CE1或200-CE3電纜，0.3和0.9米分別（不能與2.5米TK210電纜）。請注意，TK210電纜根據UL1604，危險位置不允許超過0.9 m。
遠程輸入/輸出–PROFIBUS-DPCI274板是PROFIBUS-DP現場總線，用于遠程連接S800輸入/輸出、S800L輸入/輸出、，S200輸入/輸出、S20KOLLMORGEN E33NRHA-LNN-NS-00電機0L輸入/輸出和第三方裝置最大長度為100至1200 m，取決于波特率。
S800輸入/輸出單元連接到一個或多個輸入/輸出適配器，CI830。其他單位可以是通過光纖連接到CI830適配器電纜和光纖接口單元，TB820。
S200輸入/輸出單元連接到一個或多個輸入/輸出適配器，200-APB12，最大每個適配器有八個輸入/輸出單元。CI274板充當總線主控和處理從/到的循環讀取和寫入奴隸。周期時間取決于波特率速率和連接的從屬服務器數。
最多可以使用兩個這樣的板安裝在AC 800C中。車載通信信道AC 800C有兩個車載RJ-45插孔，用于RS-232通道，一個帶全調制解調器
The inputs have a second-order, low-pass hardware filter and a digital filter with individual time constants 0.5 to 32 ms. In addition to the on-board I/O, the direct I/O system supports S200 I/O. Up to eight external I/O units can be directly plugged onto the controller and installed on the same DIN rail, and another eight I/O units can be connected via a TK210 cable (length 0.5, 1.0, or 2.5 m) and a 200-AIO adapter. A row of I/O units can be split in two by using a 200- CE1 or a 200-CE3 cable, 0.3 and 0.9 m respectively (cannot be combined with the 2.5 m TK210 cable). Note that a TK210 cable longer than 0.9 m is not allowed in hazardous locations according to UL1604. Remote I/O – PROFIBUS-DP The CI274 board is an optional interface for the PROFIBUS-DP field bus and used for remote connection of S800 I/O, S800L I/O, S200 I/O, S200L I/O and third-party units over a maximum length of 100 to 1200 m, depending on baud rate. S800 I/O units are connected to one or more I/O adapters, CI830. Additional units can be connected to the CI830 adapter via optical cables and optical interface units, TB820. S200 I/O units are connected to one or more I/O adapters, 200-APB12, with a maximum of eight I/O units per adapter. The CI274 board serves as bus master and handles cyclic reads and writes from/to the slaves. The cycle time depends on the baud rate and the number of slaves attached. A maximum of two such boards can be installed in AC 800C. On-board communication channels AC 800C has two on-board RJ-45 jacks for RS-232 channels, one with full modem
