HONEYWELL MC-PDIY22卡件,MC-PDIY22產品外觀
按鈕功能上/下
向上和向下按鈕用于在編程之前選擇密碼，并啟動“學習”或存儲目標火焰和/或可選背景火焰的過程。
目標火焰選擇目標選擇按鈕用于開始目標火焰的“學習”或存儲過程。這將自動設置火焰打開和關閉識別所需的所有開關閾值。背景火焰選擇（可選）如果應用程序存在背景火焰，可能需要將掃描儀設置為
將其與目標火焰區分開來。后臺選擇按鈕用于開始“學習”或存儲背景火焰的處理。這將自動切換“關閉”閾值（在目標期間設置火焰選擇程序），以排除背景條件。FFRT設置說明
HONEYWELL MC-PDIY22卡件用戶可以使用鍵盤將掃描儀火焰故障響應時間設置為所需的定時。
每個單元以1秒的速度來自出廠預設。將出廠默認值更改為其他
FFRT見下面的設置程序。要驗證當前FFRT設置，請按住向上推按鈕，掃描儀處于正常操作模式。“火焰強度”LED組將根據需要顯示第一、第二、第三或第四個LED，這些LED對應于FFRT（秒）。
FFRT設置程序
HONEYWELL MC-PDIY22卡件如果需要修改火焰失效響應時間，請遵循以下程序。同時按下目標火焰選擇和背景火焰選擇按鈕。
使用向上按鈕驅動LED，直到火焰強度上的LED編號[8]（通過代碼）點亮右側設置LED。同時按下目標火焰選擇和背景火焰選擇按鈕。
按向上或向下按鈕選擇所需的FFRT（所選FFRT顯示在火焰上強度LED為1、2、3或4）。選擇正確的值后，按目標火焰選擇和背景火焰選擇按鈕同時存儲。存儲的值可在正常運行模式下隨時顯示和檢查。按住向上鍵按鈕將隨時顯示右側火焰LED上存儲的FFRT。驗證已存儲正確的FFRT。
FFRT Set-Up Description
Using the keypad the scanner flame failure response time can be set by the user to the desired timing.
Each unit comes from the factory preset at 1 second. To change the factory default to a different
FFRT see Set-Up Procedure below. To verify the current FFRT setting, press and hold the UP push
button with the scanner in the normal operating mode. The “flame strength” LED set will display 1st,
2nd, 3rd or 4th LED as appropriate and these correspond to the FFRT in seconds.
FFRT Set-Up Procedure
If the Flame Failure Response Time needs modifying, follow the procedure listed below.
Press both the Target Flame Select and Background Flame Select buttons simultaneously.
Use the up button to drive the LEDs until LED number [8] (pass code) is illuminated on the flame strength
LEDs right hand set.
Press both the Target Flame Select and Background Flame Select buttons simultaneously.
Press UP or DOWN push buttons to select required FFRT (the selected FFRT is displayed on the flame
strength LEDs as either 1st, 2nd, 3rd or 4th). Once you have selected the correct value, Press both the
Target Flame Select and Background Flame Select buttons simultaneously to store. The stored value
can be displayed and checked at any time while in the normal run mode. Pressing and holding the UP
pushbutton at any time will display the stored FFRT on the flame LEDs right hand set. Verify that the
correct FFRT has been stored.
